1.12V/ 24 V system voltages are automatically recognized. 2.An upgraded 3-stage PWM charging algorithm is adopted. Application of an equalizing charging to the battery periodically or when over discharged, can effectively prevent the battery from non-equalization and sulfuration, thus extending the battery's service life. 3.With temperature compensation employed, charging parameters can be automatically adjusted. 4.A wide range of load working modes facilitate the product's application to different types of load. 5.The product provides overcharge, over-discharge, overload protection, as well as short-circuit protection. 6.By virtue of an advanced load starting method, large-capacitance loads can be started smoothly. 7.The product provides a dot matrix graphic LCD screen and a human-machine interface with a key. 8.The user-friendly design of browser and dynamic interfaces ensure convenient and intuitive operations. 9.Boasting an industrial grade design, the product can function well in various tough conditions. 10.TVS lighting protection is adopted.
Rated current 10A
System voltage Automatic recognition of 12 V/ 24 V
No-load loss < 10mA/12V;< 12mA/24V
Max. Solar energy input voltage <55V
Max. voltage at the battery end <35V
Overvoltage protection 17.0V;×2/24V;
Equalizing charging voltage 14.6V;×2/24V;
Boost charging voltage 14.4V;×2/24V;
Floating charging voltage 13.8V;×2/24V;
Charging recovery voltage 13.2V;×2/24V;
Over-discharge recovery voltage 12.6V;×2/24V;
Over-discharge voltage 11.1V;×2/24V;
Equalizing charging interval 30days
Equalizing charging time 1H
Boost charging time 2H
Temperature compensation -3.0mV/℃/2V
Light control voltage
- Light control on 5V, ×2/24V;
- Light control off 6V, ×2/24V;
Light control judgment time 1minute
Operating temperature -25℃ to +55℃;
IP protection degree IP30
Net weight 100g
Protection functions
- Solar panel short circuit and reverse-connection protection
- Over-temperature, overload and short circuit protection
Dimensions 103×71×36(mm)
1) 12V/ 24 V system voltages are automatically recognized. 2) Charging program options for sealed, GEL and flooded lead-acid batteries and lithium batteries are available. 3) An upgraded 3-stage PWM charging algorithm is adopted. Application of an equalizing charge to the battery periodically or when over discharged, can effectively prevent the battery from non-equalization and sulfuration, thus extending the battery's service life (with the exception of GEL and lithium batteries). 4) With temperature compensation employed, charging parameters can be automatically adjusted (with the exception of lithium batteries). 5) A wide range of load working modes facilitate the product's application to different types of street lights and monitoring devices. 6) The product provides overcharge, over-discharge, overload protection, as well as short-circuit and reverse-connection protection. 7) By virtue of an advanced load starting method, large-capacitance loads can be started smoothly. 8) A range of parameter settings and power-down saving functions are available ,thus requiring no repeated setting. 9) The product provides a dot matrix graphic LCD screen and a human-machine interface with 2 keys. 10)The user-friendly design of browser and animation interfaces ensures convenient and intuitive operations. 11) (An optional communication function) provides a RJ12 data port (output of TTL /MAX232 /bluetooth signals), with the data adopting the standard Modbus protocol, and can be used together with our upper computer monitoring software. 12) Boasting an industrial grade design, the product can function well in various tough conditions. 13) TVS lighting protection is adopted.
Rated current 30A
System voltage Automatic recognition of 12V/24V
No-load loss < 13mA/12V;< 15mA/24V
Max. Solar energy input voltage <55
Max. voltage at the battery end <34V
Max. voltage at the battery end Flooded FLD
Overvoltage protection 16.0V
Equalizing charging voltage 14.8
Boost charging voltage 14.6
Floating charging voltage 13.8
Charging recovery voltage 13.2V
Over-discharge recovery voltage 12.5V(settable with the keys)
Over-discharge voltage 11.0V(settable with the keys)
Equalizing charging interval 30days
Equalizing charging time 1H
Boost charging time 2H -
Temperature compensation -3.0mV/℃/2V
Light controlvoltage Light control on 5V, light control off 4 V (light control on minus 1 V)
Light control judgment time 10 minutes
USB function Yes
Operating temperature -25℃to+55℃;
IP protection degree IP30
Net weight 390g
Protection functions: attery reverse connection protection, solar panel reverse connection protection, reverse charging protection at night
Charging overload protection,overcurrent protection, short circuit protection
Dimensions(mm) 164.0×103.5×47.0
1) 12V/ 24 V system voltages are automatically recognized. 2) Charging program options for sealed, GEL and flooded lead-acid batteries and lithium batteries are available. 3) An upgraded 3-stage PWM charging algorithm is adopted. Application of an equalizing charge to the battery periodically or when over discharged, can effectively prevent the battery from non-equalization and sulfuration, thus extending the battery's service life (with the exception of GEL and lithium batteries). 4) With temperature compensation employed, charging parameters can be automatically adjusted (with the exception of lithium batteries). 5) A wide range of load working modes facilitate the product's application to different types of street lights and monitoring devices. 6) The product provides overcharge, over-discharge, overload protection, as well as short-circuit and reverse-connection protection. 7) By virtue of an advanced load starting method, large-capacitance loads can be started smoothly. 8) A range of parameter settings and power-down saving functions are available ,thus requiring no repeated setting. 9) The product provides a dot matrix graphic LCD screen and a human-machine interface with 2 keys. 10)The user-friendly design of browser and animation interfaces ensures convenient and intuitive operations. 11) (An optional communication function) provides a RJ12 data port (output of TTL /MAX232 /bluetooth signals), with the data adopting the standard Modbus protocol, and can be used together with our upper computer monitoring software. 12) Boasting an industrial grade design, the product can function well in various tough conditions. 13) TVS lighting protection is adopted.
Rated current 40A
System voltage Automatic recognition of 12V/24V
No-load loss < 13mA/12V;< 15mA/24V
Max. Solar energy input voltage <55
Max. voltage at the battery end <34V
Max. voltage at the battery end Flooded FLD
Overvoltage protection 16.0V
Equalizing charging voltage 14.8
Boost charging voltage 14.6
Floating charging voltage 13.8
Charging recovery voltage 13.2V
Over-discharge recovery voltage 12.5V(settable with the keys)
Over-discharge voltage 11.0V(settable with the keys)
Equalizing charging interval 30days
Equalizing charging time 1H
Boost charging time 2H -
Temperature compensation -3.0mV/℃/2V
Light controlvoltage Light control on 5V, light control off 4 V (light control on minus 1 V)
Light control judgment time 10 minutes
USB function Yes
Operating temperature -25℃to+55℃;
IP protection degree IP30
Net weight 390g
Protection functions: attery reverse connection protection, solar panel reverse connection protection, reverse charging protection at night
Charging overload protection,overcurrent protection, short circuit protection
Dimensions(mm) 164.0×103.5×47.0
1) 12V/ 24 V system voltages are automatically recognized. 2) Charging program options for sealed, GEL and flooded lead-acid batteries and lithium batteries are available. 3) An upgraded 3-stage PWM charging algorithm is adopted. Application of an equalizing charge to the battery periodically or when over discharged, can effectively prevent the battery from non-equalization and sulfuration, thus extending the battery's service life (with the exception of GEL and lithium batteries). 4) With temperature compensation employed, charging parameters can be automatically adjusted (with the exception of lithium batteries). 5) A wide range of load working modes facilitate the product's application to different types of street lights and monitoring devices. 6) The product provides overcharge, over-discharge, overload protection, as well as short-circuit and reverse-connection protection. 7) By virtue of an advanced load starting method, large-capacitance loads can be started smoothly. 8) A range of parameter settings and power-down saving functions are available ,thus requiring no repeated setting. 9) The product provides a dot matrix graphic LCD screen and a human-machine interface with 2 keys. 10)The user-friendly design of browser and animation interfaces ensures convenient and intuitive operations. 11) (An optional communication function) provides a RJ12 data port (output of TTL /MAX232 /bluetooth signals), with the data adopting the standard Modbus protocol, and can be used together with our upper computer monitoring software. 12) Boasting an industrial grade design, the product can function well in various tough conditions. 13) TVS lighting protection is adopted.
Rated current 60A
System voltage Automatic recognition of 12V/24V
No-load loss < 13mA/12V;< 15mA/24V
Max. Solar energy input voltage <55
Max. voltage at the battery end <34V
Max. voltage at the battery end GEL
Overvoltage protection 16.0V
Boost charging voltage 14.2
Floating charging voltage 13.8
Charging recovery voltage 13.2V
Over-discharge recovery voltage 12.5V(settable with the keys)
Over-discharge voltage 11.0V(settable with the keys)
Boost charging time 2H -
Temperature compensation -3.0mV/℃/2V
Light controlvoltage Light control on 5V, light control off 4 V (light control on minus 1 V)
Light control judgment time 10 minutes
USB function No
Operating temperature -25℃ to +55℃;
IP protection degree IP30
Net weight 650g
Protection functions: attery reverse connection protection, solar panel reverse connection protection, reverse charging protection at night
Charging overload protection,overcurrent protection, short circuit protection
Dimensions(mm) 189.27×127.2×54
The SR-HM-PWM-330W solar charge controller keeps batteries regulated and prevents them from overcharging and discharging. A DC load control feature makes this charge controller ideal for LED lights. A digital display makes monitoring current, discharge current and batter bank capacity a breeze.
Digital display shows charging current, discharge current and battery bank capacity
Dual USB ports for directly charging portable devices
3 stage charging method: bulk, absorption and floating
Ideally suited for three Flex 100 watt Solar Tech Solar panels 320-Watt and less
Maximum solar module power input: 320-Watt
Maximum solar module open circuit-Voltage inputs: 25-Volt
Maximum charging current output: 20-Amp
Nominal battery-Voltage output: 12-Volt and 24-Volt
Device is designed to flush mount, please see product manual for details
PWM technology works on only Low-Voltage panels 32 cell max. 12 or 24 volt
Liquid crystal display For status monitoring and set-up Load output Over-discharge of the battery can be prevented by connecting all loads to the load output. The load output will disconnect the load when the battery has been discharged to a pre-set voltage. Some loads (especially inverters) can best be connected directly to the battery, and the inverter remote control connected to the load output. A special interface cable may be needed, please see the manual. The connect and disconnect voltages are adjustable. Day/night timing of the load output This option allows for a pre-set ON-time after dusk. Programmable battery charge algorithm Preprogrammed algorithms for AGM, GEL, Flooded or LiFePO4 batteries (with internal BMS only) Two 5 Volt USB outputs Maximum current (both outputs combined): 2A
Liquid crystal display For status monitoring and set-up Load output Over-discharge of the battery can be prevented by connecting all loads to the load output. The load output will disconnect the load when the battery has been discharged to a pre-set voltage. Some loads (especially inverters) can best be connected directly to the battery, and the inverter remote control connected to the load output. A special interface cable may be needed, please see the manual. The connect and disconnect voltages are adjustable. Day/night timing of the load output This option allows for a pre-set ON-time after dusk. Programmable battery charge algorithm Preprogrammed algorithms for AGM, GEL, Flooded or LiFePO4 batteries (with internal BMS only) Two 5 Volt USB outputs Maximum current (both outputs combined): 2A
Liquid crystal display For status monitoring and set-up Load output Over-discharge of the battery can be prevented by connecting all loads to the load output. The load output will disconnect the load when the battery has been discharged to a pre-set voltage. Some loads (especially inverters) can best be connected directly to the battery, and the inverter remote control connected to the load output. A special interface cable may be needed, please see the manual. The connect and disconnect voltages are adjustable. Day/night timing of the load output This option allows for a pre-set ON-time after dusk. Programmable battery charge algorithm Preprogrammed algorithms for AGM, GEL, Flooded or LiFePO4 batteries (with internal BMS only) Two 5 Volt USB outputs Maximum current (both outputs combined): 2A
Liquid crystal display For status monitoring and set-up Load output Over-discharge of the battery can be prevented by connecting all loads to the load output. The load output will disconnect the load when the battery has been discharged to a pre-set voltage. Some loads (especially inverters) can best be connected directly to the battery, and the inverter remote control connected to the load output. A special interface cable may be needed, please see the manual. The connect and disconnect voltages are adjustable. Day/night timing of the load output This option allows for a pre-set ON-time after dusk. Programmable battery charge algorithm Preprogrammed algorithms for AGM, GEL, Flooded or LiFePO4 batteries (with internal BMS only) Two 5 Volt USB outputs Maximum current (both outputs combined): 2A
Liquid crystal display For status monitoring and set-up Load output Over-discharge of the battery can be prevented by connecting all loads to the load output. The load output will disconnect the load when the battery has been discharged to a pre-set voltage. Some loads (especially inverters) can best be connected directly to the battery, and the inverter remote control connected to the load output. A special interface cable may be needed, please see the manual. The connect and disconnect voltages are adjustable. Day/night timing of the load output This option allows for a pre-set ON-time after dusk. Programmable battery charge algorithm Preprogrammed algorithms for AGM, GEL, Flooded or LiFePO4 batteries (with internal BMS only) Two 5 Volt USB outputs Maximum current (both outputs combined): 2A
Liquid crystal display For status monitoring and set-up Load output Over-discharge of the battery can be prevented by connecting all loads to the load output. The load output will disconnect the load when the battery has been discharged to a pre-set voltage. Some loads (especially inverters) can best be connected directly to the battery, and the inverter remote control connected to the load output. A special interface cable may be needed, please see the manual. The connect and disconnect voltages are adjustable. Day/night timing of the load output This option allows for a pre-set ON-time after dusk. Programmable battery charge algorithm Preprogrammed algorithms for AGM, GEL, Flooded or LiFePO4 batteries (with internal BMS only) Two 5 Volt USB outputs Maximum current (both outputs combined): 2A
Liquid crystal display For status monitoring and set-up Load output Over-discharge of the battery can be prevented by connecting all loads to the load output. The load output will disconnect the load when the battery has been discharged to a pre-set voltage. Some loads (especially inverters) can best be connected directly to the battery, and the inverter remote control connected to the load output. A special interface cable may be needed, please see the manual. The connect and disconnect voltages are adjustable. Day/night timing of the load output This option allows for a pre-set ON-time after dusk. Programmable battery charge algorithm Preprogrammed algorithms for AGM, GEL, Flooded or LiFePO4 batteries (with internal BMS only) Two 5 Volt USB outputs Maximum current (both outputs combined): 2A
Load output with low battery voltage disconnect function. Lighting control function, one timer only. Two digit seven segment display for quick and easy setting of the load output functionality, including timer setting. Three stage battery charging (bulk, absorption, float), not programmable. Load output protected against over load and short circuit. Protected against reverse polarity connection of the solar array and/or battery. Day/night timing options: see manual for details
Load output with low battery voltage disconnect function. Lighting control function, one timer only. Two digit seven segment display for quick and easy setting of the load output functionality, including timer setting. Three stage battery charging (bulk, absorption, float), not programmable. Load output protected against over load and short circuit. Protected against reverse polarity connection of the solar array and/or battery. Day/night timing options: see manual for details
Load output with low battery voltage disconnect function. Lighting control function, one timer only. Two digit seven segment display for quick and easy setting of the load output functionality, including timer setting. Three stage battery charging (bulk, absorption, float), not programmable. Load output protected against over load and short circuit. Protected against reverse polarity connection of the solar array and/or battery. Day/night timing options: see manual for details
Load output with low battery voltage disconnect function. Lighting control function, one timer only. Two digit seven segment display for quick and easy setting of the load output functionality, including timer setting. Three stage battery charging (bulk, absorption, float), not programmable. Load output protected against over load and short circuit. Protected against reverse polarity connection of the solar array and/or battery. Day/night timing options: see manual for details
Load output with low battery voltage disconnect function. Lighting control function, one timer only. Two digit seven segment display for quick and easy setting of the load output functionality, including timer setting. Three stage battery charging (bulk, absorption, float), not programmable. Load output protected against over load and short circuit. Protected against reverse polarity connection of the solar array and/or battery. Day/night timing options: see manual for details
Load output with low battery voltage disconnect function. Lighting control function, one timer only. Two digit seven segment display for quick and easy setting of the load output functionality, including timer setting. Three stage battery charging (bulk, absorption, float), not programmable. Load output protected against over load and short circuit. Protected against reverse polarity connection of the solar array and/or battery. Day/night timing options: see manual for details
The BlueSolar PWM-Pro series is ready for use with its default settings.
It also is fully programmable: With help of a computer and software (available free of charge from our website) With the dedicated BlueSolar Pro Remote Panel (see features below).
Features: Lighting control function, fully programmable. Three stage battery charging (bulk, absorption, float), fully programmable. Integrated battery monitor function (Remote Panel needed to display state of charge). Load output with low voltage disconnect and manual control (default setting). Optional external temperature sensor. – Load output protected against over load and short circuit. Protected against reverse polarity connection of the solar array and/or battery.
The BlueSolar PWM-Pro series is ready for use with its default settings.
It also is fully programmable: With help of a computer and software (available free of charge from our website) With the dedicated BlueSolar Pro Remote Panel (see features below).
Features: Lighting control function, fully programmable. Three stage battery charging (bulk, absorption, float), fully programmable. Integrated battery monitor function (Remote Panel needed to display state of charge). Load output with low voltage disconnect and manual control (default setting). Optional external temperature sensor. – Load output protected against over load and short circuit. Protected against reverse polarity connection of the solar array and/or battery.
The BlueSolar PWM-Pro series is ready for use with its default settings.
It also is fully programmable: With help of a computer and software (available free of charge from our website) With the dedicated BlueSolar Pro Remote Panel (see features below).
Features: Lighting control function, fully programmable. Three stage battery charging (bulk, absorption, float), fully programmable. Integrated battery monitor function (Remote Panel needed to display state of charge). Load output with low voltage disconnect and manual control (default setting). Optional external temperature sensor. – Load output protected against over load and short circuit. Protected against reverse polarity connection of the solar array and/or battery.
The BlueSolar PWM-Pro series is ready for use with its default settings.
It also is fully programmable: With help of a computer and software (available free of charge from our website) With the dedicated BlueSolar Pro Remote Panel (see features below).
Features: Lighting control function, fully programmable. Three stage battery charging (bulk, absorption, float), fully programmable. Integrated battery monitor function (Remote Panel needed to display state of charge). Load output with low voltage disconnect and manual control (default setting). Optional external temperature sensor. – Load output protected against over load and short circuit. Protected against reverse polarity connection of the solar array and/or battery.
BlueSolar 12/24-PWM Trei modele: 5A, 10A sau 20A la 12V sau 24V * • Controler PWM cu cost redus • Senzor intern de temperatură • Încărcare baterie în trei stadii (brut, absorbţie, stabilizare) • Protecţie împotriva supracurentului • Protecţie împotriva scurt-circuitului • Protejat împotriva inversării polarităţii de la panourile solare şi/sau baterie • Cu deconectare a ieşirii de joasă tensiune • Ecran opţional la distanţă (doar la modelul de 20A)
BlueSolar 12/24-10 cu temporizator 10A la 12V sau 24V • Controler PWM pentru iluminatul solar. • Două temporizatoare pentru a activa operarea de la apus până la răsărit, ori pentru un timp limitat după apus şi un timp limitat înainte de răsărit. • Un ecran cu şapte segmente pentru vizualizarea setărilor temporizatorului şi pentru analizarea condiţiilor de eroare. • Indicator de stare a bateriei cu avertizare pentru descărcare. • Senzor intern de temperatură. • Încărcare baterie în trei stadii (brut, absorbţie, stabilizare). • Protecţie împotriva supracurentului. • Protecţie împotriva scurt-circuitului. • Protecţie împotriva inversării polarităţii de la panourile solare şi/sau baterie. • Deconectare a depăşirii sarcinii de joasă tensiune.