Photovoltaic Systems

Display: 43-63 from 630 products

49
Victron Energy Quattro 48/8000/110-100/100 230V
  • Brand: Victron Energy

Similar to the MultiPlus, the Quattro is also a combined inverter and charger. Additionally it can accept two AC inputs and automatically connect to the active source. Its many features include a true sine wave inverter, adaptive charging, hybrid PowerAssist technology plus multiple system integration features such as three or split phase operation and parallel operation.

 

Features

Two AC inputs with integrated transfer switch

The Quattro can be connected to two independent AC sources, for example the public grid and a generator, or two generators. The Quattro will automatically connect to the active source.

 

Two AC Outputs

The main output has no-break functionality. The Quattro takes over the supply to the connected loads in the event of a grid failure or when shore/generator power is disconnected. This happens so fast (less than 20 milliseconds) that computers and other electronic equipment will continue to operate without disruption. The second output is live only when AC is available on one of the inputs of the Quattro. Loads that should not discharge the battery, like a water heater for example, can be connected to this output.

 

Virtually unlimited power thanks to parallel operation

Up to 6 Quattro units can operate in parallel. Six units 48/10000/140, for example, will provide 48kW / 60kVA output power and 840 Amps charging capacity.

 

Three phase capability

Three units can be configured for three phase output. But that’s not all: up to 6 sets of three units can be parallel connected to provide 144kW / 180kVA inverter power and more than 2500A charging capacity.

 

PowerControl – Dealing with limited generator, shore side or grid power

The Quattro is a very powerful battery charger. It will therefore draw a lot of current from the generator or shore side supply (16A per 5kVA Quattro at 230VAC). A current limit can be set on each AC input. The Quattro will then take account of other AC loads and use whatever is spare for charging, thus preventing the generator or mains supply from being overloaded.

 

PowerAssist – Boosting shore or generator power

This feature takes the principle of PowerControl to a further dimension allowing the Quattro to supplement the capacity of the alternative source. Where peak power is so often required only for a limited period, the Quattro will make sure that insufficient mains or generator power is immediately compen.

 

Solar energy: AC power available even during a grid failure

The Quattro can be used in off grid as well as grid connected PV and other alternative energy systems. Loss of mains detection software is available.

 

System configuring

- In case of a stand-alone application, if settings have to be changed, this can be done in a matter of minutes with a DIP switch setting procedure.

- Parallel and three phase applications can be configured with VE.Bus Quick Configure and VE.Bus System Configuratorsoftware.

- Off grid, grid interactive and self-consumption applications, involving grid-tie inverters and/or MPPT Solar Chargers can be configured with Assistants (dedicated software for specific applications).

 

On-site Monitoring and control

Several options are available: Battery Monitor, Multi Control Panel, Ve.Net Blue Power panel, Color Control panel, smartphone or tablet (Bluetooth Smart), laptop or computer (USB or RS232).

 

Remote Monitoring and control

Victron Ethernet Remote, Venus GX and the Color Control Panel. Data can be stored and displayed on our VRM (Victron Remote Management) website, free of charge.

 

Remote configuring

When connected to the Ethernet, systems with a Color Control panel can be accessed and settings can be changed.

Read more
3669.86 EUR VAT included
The product is in stock
Details
50
Victron Energy Quattro 48/10000/140-100/100
  • Brand: Victron Energy

Similar to the MultiPlus, the Quattro is also a combined inverter and charger. Additionally it can accept two AC inputs and automatically connect to the active source. Its many features include a true sine wave inverter, adaptive charging, hybrid PowerAssist technology plus multiple system integration features such as three or split phase operation and parallel operation.

 

Features

Two AC inputs with integrated transfer switch

The Quattro can be connected to two independent AC sources, for example the public grid and a generator, or two generators. The Quattro will automatically connect to the active source.

 

Two AC Outputs

The main output has no-break functionality. The Quattro takes over the supply to the connected loads in the event of a grid failure or when shore/generator power is disconnected. This happens so fast (less than 20 milliseconds) that computers and other electronic equipment will continue to operate without disruption. The second output is live only when AC is available on one of the inputs of the Quattro. Loads that should not discharge the battery, like a water heater for example, can be connected to this output.

 

Virtually unlimited power thanks to parallel operation

Up to 6 Quattro units can operate in parallel. Six units 48/10000/140, for example, will provide 48kW / 60kVA output power and 840 Amps charging capacity.

 

Three phase capability

Three units can be configured for three phase output. But that’s not all: up to 6 sets of three units can be parallel connected to provide 144kW / 180kVA inverter power and more than 2500A charging capacity.

 

PowerControl – Dealing with limited generator, shore side or grid power

The Quattro is a very powerful battery charger. It will therefore draw a lot of current from the generator or shore side supply (16A per 5kVA Quattro at 230VAC). A current limit can be set on each AC input. The Quattro will then take account of other AC loads and use whatever is spare for charging, thus preventing the generator or mains supply from being overloaded.

 

PowerAssist – Boosting shore or generator power

This feature takes the principle of PowerControl to a further dimension allowing the Quattro to supplement the capacity of the alternative source. Where peak power is so often required only for a limited period, the Quattro will make sure that insufficient mains or generator power is immediately compen.

 

Solar energy: AC power available even during a grid failure

The Quattro can be used in off grid as well as grid connected PV and other alternative energy systems. Loss of mains detection software is available.

 

System configuring

- In case of a stand-alone application, if settings have to be changed, this can be done in a matter of minutes with a DIP switch setting procedure.

- Parallel and three phase applications can be configured with VE.Bus Quick Configure and VE.Bus System Configuratorsoftware.

- Off grid, grid interactive and self-consumption applications, involving grid-tie inverters and/or MPPT Solar Chargers can be configured with Assistants (dedicated software for specific applications).

 

On-site Monitoring and control

Several options are available: Battery Monitor, Multi Control Panel, Ve.Net Blue Power panel, Color Control panel, smartphone or tablet (Bluetooth Smart), laptop or computer (USB or RS232).

 

Remote Monitoring and control

Victron Ethernet Remote, Venus GX and the Color Control Panel. Data can be stored and displayed on our VRM (Victron Remote Management) website, free of charge.

 

Remote configuring

When connected to the Ethernet, systems with a Color Control panel can be accessed and settings can be changed.

Read more
4383.71 EUR VAT included
The product is in stock
Details
51
Victron Energy EasyPlus Compact 12/1600/70-16
  • Brand: Victron Energy

Multi-functional power solution

The EasyPlus is a multifunctional energy system consisting of a powerful sine wave inverter, a sophisticated battery charger, a high speed AC transfer switch and AC distribution in a single light weight and compact enclosure. The system has been designed for those who want to enjoy the comfort and freedom of a complete energy system without spending time on the installation of separate components and difficult technical procedures.

 

Optimum comfort and safety

The EasyPlus guarantees uninterrupted power supply, whenever and wherever you are. Where shore or generator power is limited, the unique PowerAssist® technology makes it possible to boost the total capacity by adding extra energy from the batteries. Optimum safety is guaranteed with the integrated RCD (Residual Current Device) protecting against earth leakage.

 

5 step installation: quick and easy

The EasyPlus gets its name from the simplicity of installation and use. The system can be installed within five simple steps making significant savings in time as well as space. The EasyPlus provides plugs and sockets for all AC connections and is supplied with the battery cables already fitted so you can save hours in installation time.

 

Step 1. Select a suitable place for the EasyPlus (as close as possible to the batteries) and install the wall mounting bracket. Attach the EasyPlus to the bracket and secure it with the screws provided.

Step 2. Connect the shore/generator input power and the outgoing circuits (including dedicated water heater feed) to the EasyPlus.

Step 3. Connect the control panel (optional) with the UTP patch lead.

Step 4. Connect the battery cables and temperature sensor to the batteries (also supplied as standard).

Step 5. Switch on the RCD, the AC distribution and the inverter/charger and the system is ready to use.

Read more
1288.76 EUR VAT included
The product is in stock
Details
52
Victron Energy MultiGrid 24/3000/70-50 230V
  • Brand: Victron Energy

MultiGrid smooths out the risk of grid instability and energy costs by utilising energy storage and self-consumption. MultiGrid, is the VDE-AR-N 4105 and AU 4777.2:2015 approved, CEC listed version of the MultiPlus. With Anti-Islanding built in, this makes it suitable for countries such as Germany, Austria and others. In the UK the MultiPlus is used, as it is approved to the G83/2 and G59-3-1 standards required there.

Combined with the flexibility of a MultiPlus bidirectional converter The MultiPlus range of bidirectional converters is the worldwide product of choice on boats and vehicles to generate AC power, and to recharge batteries, either with shore power or an onboard AC generator. The MultiPlus also is the industry standard in on-grid and off-grid energy storage systems and is approved for use in energy storage and self-consumption systems in the UK (G83/2 and G59-3-1 standards).

Several hardware and firmware modifications were needed to qualify for VDE-AR-N 4105 and several other country specific energy storage related standards. The resulting product is the MultiGrid.

The MultiGrid fits seamlessly in all common energy storage topologies There is no one-size-fits-all solution to energy storage. The building blocks, topology and control systems will depend on local conditions and regulations.

Read more
1240,00 EUR 1050.00 EUR VAT included
The product is in stock
-15%
Details
53
Victron Energy MultiGrid 48/3000/35-50 230V
  • Brand: Victron Energy

MultiGrid smooths out the risk of grid instability and energy costs by utilising energy storage and self-consumption. MultiGrid, is the VDE-AR-N 4105 and AU 4777.2:2015 approved, CEC listed version of the MultiPlus. With Anti-Islanding built in, this makes it suitable for countries such as Germany, Austria and others. In the UK the MultiPlus is used, as it is approved to the G83/2 and G59-3-1 standards required there.

Combined with the flexibility of a MultiPlus bidirectional converter The MultiPlus range of bidirectional converters is the worldwide product of choice on boats and vehicles to generate AC power, and to recharge batteries, either with shore power or an onboard AC generator. The MultiPlus also is the industry standard in on-grid and off-grid energy storage systems and is approved for use in energy storage and self-consumption systems in the UK (G83/2 and G59-3-1 standards). Several hardware and firmware modifications were needed to qualify for VDE-AR-N 4105 and several other country specific energy storage related standards. The resulting product is the MultiGrid. The MultiGrid fits seamlessly in all common energy storage topologies There is no one-size-fits-all solution to energy storage. The building blocks, topology and control systems will depend on local conditions and regulations. The MultiGrid hardware, together with a wide range of software tools, seamlessly fits in all common topologies, shown in the pictures below. More detail can be found in our Energy Storage brochure. MultiGrid
Read more
1119.00 EUR VAT included
Available on order
Details
54
Victron Energy EasySolar 12/1600/70-16 MPPT 100/50 Inverter/Solar Charger
  • Brand: Victron Energy

All-in-one solar power solution

The EasySolar combines a MPPT Solar Charge Controller, an inverter/charger and AC distribution in one enclosure. The product is easy to install, with a minimum of wiring.

The Solar Charge ControllerBlueSolar MPPT 100/50

Up to three strings of PV panels can be connected with three sets of MC4 (PV-ST01) PV connectors.

The inverter/charger: MultiPlus Compact 12/1600/70 or 24/1600/40

The MPPT Charge Controller and the MultiPlus Compact Inverter/Charger share the DC battery cables (included). The batteries can be charged with solar power (BlueSolar MPPT) and/or with AC power (inverter/charger) from the utility grid or a genset.

EasySolar 24V and 48V, 3000VA

All-in-one solar power solution

The EasySolar combines two MPPT Solar Charge Controllers and an inverter/charger in one enclosure. The product is easy to install, with a minimum of wiring.

Two solar charge controllers:2x BlueSolar MPPT 100/50, 0r 2x BlueSolar MPPT 150/35

Up to six strings of PV panels can be connected to six sets of MC4 (PV - ST01) PV connectors.

The inverter/charger: MultiPlus Compact

24/3000/70-50 or 48/3000/35-50

 

The MPPT Charge Controllers and the MultiPlus Inverter/Charger share the DC battery connection. The batteries can be charged with solar power (2x BlueSolar MPPT) and/or with AC power (inverter/charger) from the utility grid or a genset.

Read more
1380.00 EUR VAT included
Available on order
Details
55
Victron Energy EasySolar 24/1600/40-16 230V MPPT 100/50 Inverter/Solar Charger
  • Brand: Victron Energy

The EasySolar combines a MPPT Solar Charge Controller, an inverter/charger and AC distribution in one enclosure. The product is easy to install, with a minimum of wiring.

 

All-in-one solar power solution

The EasySolar combines a MPPT solar charge controller, an inverter/charger and AC distribution in one enclosure. The product is easy to install, with a minimum of wiring

 

The solar charge controller: Blue Solar MPPT 100/50

Up to three strings of PV panels can be connected to three sets of MC4 (PV-ST01) PV connectors.

 

The inverter/charger: MultiPlus Compact 24/1600/40

The MPPT charge controller and the MultiPlus Compact inverter/charger share the DC battery cables (included). The batteries can be charged with solar power (BlueSolar MPPT) and/or with AC power (inverter/charger) from the utility grid or a genset.

 

AC distribution

The AC distribution consists of a RCD (30 mA/16 A) and four AC outputs protected by two 10A and two 16A circuit breakers. One 16A output is controlled by the AC input: it will switch on only when AC is available.

 

PowerAssist

Unique PowerAssist technology protects the utility or generator supply from being overloaded by adding extra inverter power when needed.

 

Unique solar application software

Several software programs (Assistants) are available to configure the system for various grid interactive or stand-alone applications.

Read more
1685.21 EUR VAT included
The product is in stock
Details
56
Victron Energy EasySolar 48/3000/35-50 MPPT 150/70 Color Control
  • Brand: Victron Energy

All-in-one solar power solution

The EasySolar combines a MPPT Solar Charge Controller, an inverter/charger and AC distribution in one enclosure. The product is easy to install, with a minimum of wiring.

The all-in-one solar power solution The EasySolar combines a MPPT solar charge controller, an inverter/charger and AC distribution in one enclosure. The product is easy to install, with a minimum of wiring. 
 
Color Control panel Two outstanding functions: - Prioritizes battery charging by the MPPT charge controller  - Connects to the internet, enabling remote monitoring (VRM website) and remote control. 
 
AC distribution The AC distribution consists of a RCD (30mA / 63A) and four AC outputs protected by two 10A and two 16A circuit breakers. An additional 16A output is controlled by the AC input: it will switch on only when AC is available. 
 
PowerAssist Unique PowerAssist technology protects the utility or generator supply from being overloaded by adding extra inverter power when needed. 
 

Read more
2025.00 EUR VAT included
Available on order
Details
57
Inverter 12V 250VA Victron Energy Phoenix VE.Direct NEMA 5-12R
  • Brand: Victron Energy

Product Code

PIN122510500

Model

Phoenix

Output

230VAC +/- 3% 50Hz or 60Hz +/- 0,1%

Cont. output power at 25°C (W)

200

Peak power (W)

350

Maximum efficiency (%)

87

Protection

output short circuit, overload, battery voltage too high, battery voltage too low, temperature too high, DC ripple too high

Safety

EN/IEC 60335-1 / EN/IEC 62109-1

Dimensions (D x W x H)

86x165x260 mm

Net Weight

2.4 Kg

Waveform

Pure Sine Wave

Rated Power W

200W

Battery Voltage V

12 V

Read more
123.37 EUR VAT included
The product is in stock
Details
58
Inverter 12V 375VA Victron Energy Phoenix VE.Direct NEMA 5-15R
  • Brand: Victron Energy

 

Product Code

PIN123750500

Model

Phoenix

Output

230VAC +/- 3% 50Hz or 60Hz +/- 0,1%

Cont. output power at 25°C (W)

375

Cont. output power at 40°C (W)

300

Maximum efficiency (%)

89

Protection

output short circuit, overload, battery voltage too high, battery voltage too low, temperature too high, DC ripple too high

Safety

EN/IEC 60335-1 / EN/IEC 62109-1

Dimensions (D x W x H)

86x165x260 mm

Net Weight

3 Kg

Waveform

Pure Sine Wave

Rated Power W

300W

Battery Voltage V

12 V


 
Read more
150.91 EUR VAT included
The product is in stock
Details
59
Inverter 12V 500VA Victron Energy Phoenix VE.Direct NEMA 5-15R
  • Brand: Victron Energy

Inverters allow you to power domestic equipment - requiring 230V/120V AC - using 'leisure' or 'automotive' batteries rated at 12V, 24V or 48V DC.

 

Highly Reliable - built for the years ahead

Phoenix Inverters are built to last. They feature sophisticated full-bridge and toroidal transformer topology - which is suitable for powering sensitive electronics. They are overload, temperature, and short-circuit protected.

 

Full bursts - High Peak output

Some electronic devices - particularly those which have an electric motor - require short burst of energy on start-up which is much higher than their rated power consumption. No problem - the Phoenix inverter has industry-leading peak-power capability.

 

Intelligent alarms, shut-downs, and re-starts

A high power draw on start-up can trigger false alarms, and shut-downs. Phoenix makes allowance for this and only shuts down in cases of persistent overload. Intelligently - shut downs will be followed by a series of re-starts - to eliminate 'false alarms'.

 

Conserve power with Eco mode

In Eco mode the inverter shuts down when no power is required. Phoenix senses the output socket every couple of seconds and automatically turns back on if power is again required.

 

User-configurable settings

Phoenix has a communication port providing access to status information, alarms and automatic user-configurable low-voltage shut downs. Shut downs will be followed by a series of intelligent re-start attempts. User settings can be accessed from your computer or mobile device via VictronConnect - our free-to-use app.

 

Features

VE.Direct communication port

The VE.Direct port can be connected to:

• A computer (VE.Direct to USB interface cable needed)

• Apple and Android smartphones, tablets, MacBook’s and other devices (VE.Direct Bluetooth Smart dongle needed)

 

Fully configurable:

• Low battery voltage alarm trip and reset levels

• Low battery voltage cut-off and restart levels

• Dynamic cut-off: load dependent cut-off level

• Output voltage 210 - 245V

• Frequency 50 Hz or 60 Hz

• ECO mode on/off and ECO mode sense level

 

Monitoring:

• In- and output voltage, % load and alarms

 

Proven reliability

The full bridge plus toroidal transformer topology has proven its reliability over many years. The inverters are short circuit proof and protected against overheating, whether due to overload or high ambient temperature.

 

High start-up power

Needed to start loads such as power converters for LED lamps, halogen lamps or electric tools.

 

ECO mode

When in ECO mode, the inverter will switch to standby when the load decreases below a preset value (min load: 15W). Once in standby the inverter will switch on for a short period (adjustable, default: every 2,5 seconds). If the load exceeds a preset level, the inverter will remain on.

 

Remote on/off

A remote on/off switch can be connected to a two pole connector, or between battery plus and the left hand contact of the two pole connector.

 

LED diagnosis

Please see manual for a description.

 

To transfer the load to another AC source: the automatic transfer switch

For our low power inverters we recommend our Filax Automatic Transfer Switch. The Filax features a very short switchover time (less than 20 milliseconds) so that computers and other electronic equipment will continue to operate without disruption.

 

Available with different output sockets

Schuko, UK, AU/NZ, IEC-320, Nema 5-15R

 

DC connection with screw terminals

No special tools needed for installation

 

Full Specifications

  • Part Number : PIN125010500
  • Manufacturer : Victron Energy
  • Output Wave Form : Pure Sine Wave
  • Voltage (V) : 12
  • Frequency (Hz) : 50Hz or 60Hz
  • Watts : 400
  • Peak Power (W) : 900
  • Continuous Output Power (VA) : 500
  • Length (Mm) : 275
  • Width (Mm) : 172
  • Height (Mm) : 86
  • Manufactured Weight (Kg) : 3.9
  • Remote Control : No
Read more
189.24 EUR VAT included
The product is in stock
Details
60
Inverter 24V 250VA Victron Energy Phoenix VE.Direct NEMA 5-15R
  • Brand: Victron Energy
 
Product Code PIN242510500
Model Phoenix
Output 230VAC +/- 3% 50Hz or 60Hz +/- 0,1%
Cont. output power at 25°C (W) 200
Peak power (W) 350
Maximum efficiency (%) 88
Protection output short circuit, overload, battery voltage too high, battery voltage too low, temperature too high, DC ripple too high
Safety EN/IEC 60335-1 / EN/IEC 62109-1
Dimensions (DxWxH)  86x165x260 mm
Net Weight 2.4 Kg
Waveform Pure Sine Wave
Rated Power W 200W
Battery Voltage V 24 V


 
Read more
123.37 EUR VAT included
The product is in stock
Details
61
Inverter 24V 375VA Victron Energy Phoenix VE.Direct NEMA 5-15R
  • Brand: Victron Energy
 
Product Code PIN243750500
Model Phoenix
Output 230VAC +/- 3% 50Hz or 60Hz +/- 0,1%
Cont. output power at 25°C (W) 375
Cont. output power at 40°C (W) 300
Maximum efficiency (%) 89
Protection output short circuit, overload, battery voltage too high, battery voltage too low, temperature too high, DC ripple too high
Safety EN/IEC 60335-1 / EN/IEC 62109-1
Dimensions (DxWxH) 86x165x260 mm
Net Weight 2.4 Kg
Waveform Pure Sine Wave
Rated Power W 300W
Battery Voltage V 24 V
Read more
150.91 EUR VAT included
The product is in stock
Details
62
Inverter 24V 800VA Victron Energy Phoenix VE.Direct NEMA 5-15R
  • Brand: Victron Energy

Inverters allow you to power domestic equipment - requiring 230V/120V AC - using 'leisure' or 'automotive' batteries rated at 12V, 24V or 48V DC. 

 

Highly Reliable - built for the years ahead

Phoenix Inverters are built to last. They feature sophisticated full-bridge and toroidal transformer topology - which is suitable for powering sensitive electronics. They are overload, temperature, and short-circuit protected.

 

Full bursts - High Peak output

Some electronic devices - particularly those which have an electric motor - require short burst of energy on start-up which is much higher than their rated power consumption. No problem - the Phoenix inverter has industry-leading peak-power capability.

 

Intelligent alarms, shut-downs, and re-starts

A high power draw on start-up can trigger false alarms, and shut-downs. Phoenix makes allowance for this and only shuts down in cases of persistent overload. Intelligently - shut downs will be followed by a series of re-starts - to eliminate 'false alarms'.

 

Conserve power with Eco mode

In Eco mode the inverter shuts down when no power is required. Phoenix senses the output socket every couple of seconds and automatically turns back on if power is again required.

 

User-configurable settings

Phoenix has a communication port providing access to status information, alarms and automatic user-configurable low-voltage shut downs. Shut downs will be followed by a series of intelligent re-start attempts. User settings can be accessed from your computer or mobile device via VictronConnect - our free-to-use app.

 

Features

VE.Direct communication port

The VE.Direct port can be connected to:

• A computer (VE.Direct to USB interface cable needed)

• Apple and Android smartphones, tablets, MacBook’s and other devices (VE.Direct Bluetooth Smart dongle needed)

 

Fully configurable:

• Low battery voltage alarm trip and reset levels

• Low battery voltage cut-off and restart levels

• Dynamic cut-off: load dependent cut-off level

• Output voltage 210 - 245V

• Frequency 50 Hz or 60 Hz

• ECO mode on/off and ECO mode sense level

 

Monitoring:

• In- and output voltage, % load and alarms

 

Proven reliability

The full bridge plus toroidal transformer topology has proven its reliability over many years. The inverters are short circuit proof and protected against overheating, whether due to overload or high ambient temperature.

 

High start-up power

Needed to start loads such as power converters for LED lamps, halogen lamps or electric tools.

 

ECO mode

When in ECO mode, the inverter will switch to standby when the load decreases below a preset value (min load: 15W). Once in standby the inverter will switch on for a short period (adjustable, default: every 2,5 seconds). If the load exceeds a preset level, the inverter will remain on.

 

Remote on/off

A remote on/off switch can be connected to a two pole connector, or between battery plus and the left hand contact of the two pole connector.

 

LED diagnosis

Please see manual for a description.

 

To transfer the load to another AC source: the automatic transfer switch

For our low power inverters we recommend our Filax Automatic Transfer Switch. The Filax features a very short switchover time (less than 20 milliseconds) so that computers and other electronic equipment will continue to operate without disruption.

 

DC connection with screw terminals

No special tools needed for installation

 

Full Specifications

  • Part Number : PIN241800500
  • Manufacturer : Victron Energy
  • Output Wave Form : Pure Sine Wave
  • Voltage (V) : 24
  • Frequency (Hz) : 50Hz or 60Hz
  • Watts : 650
  • Peak Power (W) : 1500W
  • Continuous Output Power (VA) : 800
  • Length (Mm) : 105
  • Width (Mm) : 216
  • Height (Mm) : 305
  • Manufactured Weight (Kg) : 5.5
  • Remote Control : No
Read more
323.39 EUR VAT included
The product is in stock
Details
63
Phoenix Inverter 48/375 VE. Direct NEMA 5-15R
  • Brand: Victron Energy

Highly Reliable - built for the years ahead

Phoenix Inverters are built to last. They feature sophisticated full-bridge and toroidal transformer topology - which is suitable for powering sensitive electronics. They are overload, temperature, and short-circuit protected.

 

Full bursts - High Peak output

Some electronic devices - particularly those which have an electric motor - require short burst of energy on start-up which is much higher than their rated power consumption. No problem - the Phoenix inverter has industry-leading peak-power capability.

 

Intelligent alarms, shut-downs, and re-starts

A high power draw on start-up can trigger false alarms, and shut-downs. Phoenix makes allowance for this and only shuts down in cases of persistent overload. Intelligently - shut downs will be followed by a series of re-starts - to eliminate 'false alarms'.

 

Conserve power with Eco mode

In Eco mode the inverter shuts down when no power is required. Phoenix senses the output socket every couple of seconds and automatically turns back on if power is again required.

 

User-configurable settings

Phoenix has a communication port providing access to status information, alarms and automatic user-configurable low-voltage shut downs. Shut downs will be followed by a series of intelligent re-start attempts. User settings can be accessed from your computer or mobile device via VictronConnect - our free-to-use app.

 

Features

VE.Direct communication port

The VE.Direct port can be connected to:

• A computer (VE.Direct to USB interface cable needed)

• Apple and Android smartphones, tablets, MacBook’s and other devices (VE.Direct Bluetooth Smart dongle needed)

 

Fully configurable:

• Low battery voltage alarm trip and reset levels

• Low battery voltage cut-off and restart levels

• Dynamic cut-off: load dependent cut-off level

• Output voltage 210 - 245V

• Frequency 50 Hz or 60 Hz

• ECO mode on/off and ECO mode sense level

 

Monitoring:

• In- and output voltage, % load and alarms

 

Proven reliability

The full bridge plus toroidal transformer topology has proven its reliability over many years. The inverters are short circuit proof and protected against overheating, whether due to overload or high ambient temperature.

 

High start-up power

Needed to start loads such as power converters for LED lamps, halogen lamps or electric tools.

 

ECO mode

When in ECO mode, the inverter will switch to standby when the load decreases below a preset value (min load: 15W). Once in standby the inverter will switch on for a short period (adjustable, default: every 2,5 seconds). If the load exceeds a preset level, the inverter will remain on.

 

Remote on/off

A remote on/off switch can be connected to a two pole connector, or between battery plus and the left hand contact of the two pole connector.

 

LED diagnosis

Please see manual for a description.

 

To transfer the load to another AC source: the automatic transfer switch

For our low power inverters we recommend our Filax Automatic Transfer Switch. The Filax features a very short switchover time (less than 20 milliseconds) so that computers and other electronic equipment will continue to operate without disruption.

 

DC connection with screw terminals

No special tools needed for installation

 

Full Specifications

  • Part Number : PIN483750500
  • Manufacturer : Victron Energy
  • Output Wave Form : Pure Sine Wave
  • Voltage (V) : 48
  • Frequency (Hz) : 50Hz or 60Hz
  • Watts : 300
  • Peak Power (W) : 700
  • Continuous Output Power (VA) : 375
  • Length (Mm) : 260
  • Width (Mm) : 165
  • Height (Mm) : 86
  • Manufactured Weight (Kg) : 3
  • Remote Control : No
Read more
150.91 EUR VAT included
The product is in stock
Details
64
Phoenix Inverter 48/500 VE. Direct NEMA 5-15R
  • Brand: Victron Energy

Highly Reliable - built for the years ahead

Phoenix Inverters are built to last. They feature sophisticated full-bridge and toroidal transformer topology - which is suitable for powering sensitive electronics. They are overload, temperature, and short-circuit protected.

 

Full bursts - High Peak output

Some electronic devices - particularly those which have an electric motor - require short burst of energy on start-up which is much higher than their rated power consumption. No problem - the Phoenix inverter has industry-leading peak-power capability.

 

Intelligent alarms, shut-downs, and re-starts

A high power draw on start-up can trigger false alarms, and shut-downs. Phoenix makes allowance for this and only shuts down in cases of persistent overload. Intelligently - shut downs will be followed by a series of re-starts - to eliminate 'false alarms'.

 

Conserve power with Eco mode

In Eco mode the inverter shuts down when no power is required. Phoenix senses the output socket every couple of seconds and automatically turns back on if power is again required.

 

User-configurable settings

Phoenix has a communication port providing access to status information, alarms and automatic user-configurable low-voltage shut downs. Shut downs will be followed by a series of intelligent re-start attempts. User settings can be accessed from your computer or mobile device via VictronConnect - our free-to-use app.

 

Features

VE.Direct communication port

The VE.Direct port can be connected to:

• A computer (VE.Direct to USB interface cable needed)

• Apple and Android smartphones, tablets, MacBook’s and other devices (VE.Direct Bluetooth Smart dongle needed)

 

Fully configurable:

• Low battery voltage alarm trip and reset levels

• Low battery voltage cut-off and restart levels

• Dynamic cut-off: load dependent cut-off level

• Output voltage 210 - 245V

• Frequency 50 Hz or 60 Hz

• ECO mode on/off and ECO mode sense level

 

Monitoring:

• In- and output voltage, % load and alarms

 

Proven reliability

The full bridge plus toroidal transformer topology has proven its reliability over many years. The inverters are short circuit proof and protected against overheating, whether due to overload or high ambient temperature.

 

High start-up power

Needed to start loads such as power converters for LED lamps, halogen lamps or electric tools.

 

ECO mode

When in ECO mode, the inverter will switch to standby when the load decreases below a preset value (min load: 15W). Once in standby the inverter will switch on for a short period (adjustable, default: every 2,5 seconds). If the load exceeds a preset level, the inverter will remain on.

 

Remote on/off

A remote on/off switch can be connected to a two pole connector, or between battery plus and the left hand contact of the two pole connector.

 

LED diagnosis

Please see manual for a description.

 

To transfer the load to another AC source: the automatic transfer switch

For our low power inverters we recommend our Filax Automatic Transfer Switch. The Filax features a very short switchover time (less than 20 milliseconds) so that computers and other electronic equipment will continue to operate without disruption.

 

DC connection with screw terminals

No special tools needed for installation

 

Full Specifications

  • Part Number : PIN485010500
  • Manufacturer : Victron Energy
  • Output Wave Form : Pure Sine Wave
  • Voltage (V) : 48
  • Frequency (Hz) : 50Hz or 60Hz
  • Watts : 400
  • Peak Power (W) : 900
  • Continuous Output Power (VA) : 500
  • Length (Mm) : 275
  • Width (Mm) : 172
  • Height (Mm) : 86
  • Manufactured Weight (Kg) : 3.9
  • Remote Control : No
Read more
189.24 EUR VAT included
The product is in stock
Details
65
Phoenix Inverter 48/800 VE. Direct NEMA 5-15R
  • Brand: Victron Energy

Highly Reliable - built for the years ahead

Phoenix Inverters are built to last. They feature sophisticated full-bridge and toroidal transformer topology - which is suitable for powering sensitive electronics. They are overload, temperature, and short-circuit protected.

 

Full bursts - High Peak output

Some electronic devices - particularly those which have an electric motor - require short burst of energy on start-up which is much higher than their rated power consumption. No problem - the Phoenix inverter has industry-leading peak-power capability.

 

Intelligent alarms, shut-downs, and re-starts

A high power draw on start-up can trigger false alarms, and shut-downs. Phoenix makes allowance for this and only shuts down in cases of persistent overload. Intelligently - shut downs will be followed by a series of re-starts - to eliminate 'false alarms'.

 

Conserve power with Eco mode

In Eco mode the inverter shuts down when no power is required. Phoenix senses the output socket every couple of seconds and automatically turns back on if power is again required.

 

User-configurable settings

Phoenix has a communication port providing access to status information, alarms and automatic user-configurable low-voltage shut downs. Shut downs will be followed by a series of intelligent re-start attempts. User settings can be accessed from your computer or mobile device via VictronConnect - our free-to-use app.

 

Features

VE.Direct communication port

The VE.Direct port can be connected to:

• A computer (VE.Direct to USB interface cable needed)

• Apple and Android smartphones, tablets, MacBook’s and other devices (VE.Direct Bluetooth Smart dongle needed)

 

Fully configurable:

• Low battery voltage alarm trip and reset levels

• Low battery voltage cut-off and restart levels

• Dynamic cut-off: load dependent cut-off level

• Output voltage 210 - 245V

• Frequency 50 Hz or 60 Hz

• ECO mode on/off and ECO mode sense level

 

Monitoring:

• In- and output voltage, % load and alarms

 

Proven reliability

The full bridge plus toroidal transformer topology has proven its reliability over many years. The inverters are short circuit proof and protected against overheating, whether due to overload or high ambient temperature.

 

High start-up power

Needed to start loads such as power converters for LED lamps, halogen lamps or electric tools.

 

ECO mode

When in ECO mode, the inverter will switch to standby when the load decreases below a preset value (min load: 15W). Once in standby the inverter will switch on for a short period (adjustable, default: every 2,5 seconds). If the load exceeds a preset level, the inverter will remain on.

 

Remote on/off

A remote on/off switch can be connected to a two pole connector, or between battery plus and the left hand contact of the two pole connector.

 

LED diagnosis

Please see manual for a description.

 

To transfer the load to another AC source: the automatic transfer switch

For our low power inverters we recommend our Filax Automatic Transfer Switch. The Filax features a very short switchover time (less than 20 milliseconds) so that computers and other electronic equipment will continue to operate without disruption.

 

DC connection with screw terminals

No special tools needed for installation

 

Full Specifications

  • Part Number : PIN481800500
  • Manufacturer : Victron Energy
  • Output Wave Form : Pure Sine Wave
  • Voltage (V) : 48
  • Frequency (Hz) : 50Hz or 60Hz
  • Watts : 650
  • Peak Power (W) : 1500
  • Continuous Output Power (VA) : 800
  • Length (Mm) : 305
  • Width (Mm) : 216
  • Height (Mm) : 105
  • Manufactured Weight (Kg) : 5.5
  • Remote Control : No
Read more
323.39 EUR VAT included
The product is in stock
Details
66
Victron Energy MultiPlus Compact 24/2000/50-50 120V
  • Brand: Victron Energy

Victron Energy Part Number: CMP242200100 or MultiPlus Compact 24/2000/50-50

MultiPlus Compact 24/2000/50-50 Features:

  • PowerControl: YES
  • PowerAssist: YES
  • Transfer switch (A): 50A
  • Parallel and 3-phase operation: YES

 

MultiPlus Compact 12/2000/50-50 Specifications:

  • Input voltage range (V DC): 9.5 – 17V
  • Output: 120V 60Hz
  • Cont. output power at 25 °C (VA): 2000
  • Cont. output power at 25 °C (W): 1600
  • Cont. output power at 40 °C (W): 1450
  • Peak power (W): 4000
  • Maximum efficiency (%): 92
  • Zero-load power (W): 9
  • Zero load power in AES mode (W): 7
  • Zero load power in Search mode (W): 3

 

Charger Specifications:

  • Charge voltage ‘absorption’ (V DC): 14.4
  • Charge voltage ‘float’ (V DC): 13.8
  • Storage mode (V DC): 13.2
  • Charge current house battery (A): 50
  • Charge current starter battery (A): 4
  • Battery temperature sensor: YES
  • Weight: 25 lbs
  • Dimensions (H x W x D): 20.5″ x 10″ x 5″

 

Multifunctional, with intelligent power management
The MultiPlus is a powerful true sine wave inverter, a sophisticated battery charger that features adaptive charge technology, and a high-speed AC transfer switch in a single compact enclosure. Next to these primary functions, the MultiPlus has several advanced features, as outlined below.

Two AC Outputs
The main output has no-break functionality. The MultiPlus takes over the supply to the connected loads in the event of a grid failure or when shore/generator power is disconnected. This happens so fast (less than 20 milliseconds) that computers and other electronic equipment will continue to operate without disruption. The second output is live only when AC is available on one of the inputs of the MultiPlus. Loads that should not discharge the battery, like a water heater for example, can be connected to this output (second output available on models rated at 3kVA and more).

Virtually unlimited power thanks to parallel operation
Up to 6 Multis can operate in parallel to achieve higher power output. Six 24/5000/120 units, for example, will provide 25 kW / 30 kVA output power with 720 Amps charging capacity.

Three phase capability
In addition to parallel connection, three units of the same model can be configured for three-phase output. But that’s not all: up to 6 sets of three units can be parallel connected for a huge 75 kW / 90 kVA inverter and more than 2000 Amps charging capacity.

PowerControl – Dealing with limited generator, shore side or grid power
The MultiPlus is a very powerful battery charger. It will therefore draw a lot of current from the generator or shore side supply (nearly 10A per 5kVA Multi at 230VAC). With the Multi Control Panel a maximum generator or shore current can be set. The MultiPlus will then take account of other AC loads and use whatever is extra for charging, thus preventing the generator or shore supply from being overloaded.

PowerAssist – Boosting the capacity of shore or generator power
This feature takes the principle of PowerControl to a further dimension. It allows the MultiPlus to supplement the capacity of the alternative source. Where peak power is so often required only for a limited period, the MultiPlus will make sure that insufficient shore or generator power is immediately compensated for by power from the battery. When the load reduces, the spare power is used to recharge the battery.

Four stage adaptive charger and dual bank battery charging
The main output provides a powerful charge to the battery system by means of advanced ‘adaptive charge’ software. The software fine-tunes the three stage automatic process to suit the condition of the battery, and adds a fourth stage for long periods of float charging. In addition to this, the MultiPlus will charge a second battery using an independent trickle charge output intended for a main engine or generator starter battery (trickle charge output available on 12V and 24V models only).

System configuring has never been easier
After installation, the MultiPlus is ready to go. If settings have to be changed, this can be done in a matter of minutes with a new DIP switch setting procedure. Even parallel and 3-phase operation can be programmed with DIP switches: no computer needed! Alternatively, VE.Net can be used instead of the DIP switches. And sophisticated software (VE.Bus Quick Configure and VE.Bus System Configurator) is available to configure several new, advanced, features

Read more
1219.29 EUR VAT included
The product is in stock
Details
67
Victron Energy Quattro 12/5000/200-100/100 120V
  • Brand: Victron Energy

Two AC inputs with integrated transfer switch

The Quattro can be connected to two independent AC sources, for example shore-side power and a generator, or two generators. The Quattro will automatically connect to the active source. The main output has no-break functionality. In the event of a grid failure, or shore or generator power being disconnected, the Quattro takes over the supply to the connected loads. This happens so fast (less than 20 milliseconds) that computers and other electronic equipment will continue to operate without disruption. The second output is live only when AC is available on one of the inputs of the Quattro. Loads that should not discharge the battery, such as air-conditioning or a water heater can be connected to this output.

Unique PowerAssist feature

The Quattro will prevent overload of a limited AC source. First, battery charging will automatically be reduced when otherwise an overload would occur. The second level will boost the output of a generator or shore side supply with power taken from the battery.

Virtually unlimited power thanks to parallel operation

Up to 6 Quattros can operate in parallel to achieve higher power output. Three phase or split phase operation is also possible.

Read more
4014.80 EUR VAT included
The product is in stock
Details
68
Victron Energy Quattro 24/5000/120-100/100 120VAC
  • Brand: Victron Energy

Two AC inputs with integrated transfer switch

The Quattro can be connected to two independent AC sources, for example shore-side power and a generator, or two generators. The Quattro will automatically connect to the active source. The main output has no-break functionality. In the event of a grid failure, or shore or generator power being disconnected, the Quattro takes over the supply to the connected loads. This happens so fast (less than 20 milliseconds) that computers and other electronic equipment will continue to operate without disruption. The second output is live only when AC is available on one of the inputs of the Quattro. Loads that should not discharge the battery, such as air-conditioning or a water heater can be connected to this output.

Unique PowerAssist feature

The Quattro will prevent overload of a limited AC source. First, battery charging will automatically be reduced when otherwise an overload would occur. The second level will boost the output of a generator or shore side supply with power taken from the battery.

Virtually unlimited power thanks to parallel operation

Up to 6 Quattros can operate in parallel to achieve higher power output. Three phase or split phase operation is also possible.

Read more
3533.33 EUR VAT included
The product is in stock
Details
69
Victron Energy Quattro 48/3000/35-50/50 120VAC
  • Brand: Victron Energy

Two AC inputs with integrated transfer switch

The Quattro can be connected to two independent AC sources, for example shore-side power and a generator, or two generators. The Quattro will automatically connect to the active source. The main output has no-break functionality. In the event of a grid failure, or shore or generator power being disconnected, the Quattro takes over the supply to the connected loads. This happens so fast (less than 20 milliseconds) that computers and other electronic equipment will continue to operate without disruption. The second output is live only when AC is available on one of the inputs of the Quattro. Loads that should not discharge the battery, such as air-conditioning or a water heater can be connected to this output.

Unique PowerAssist feature

The Quattro will prevent overload of a limited AC source. First, battery charging will automatically be reduced when otherwise an overload would occur. The second level will boost the output of a generator or shore side supply with power taken from the battery.

Virtually unlimited power thanks to parallel operation

Up to 6 Quattros can operate in parallel to achieve higher power output. Three phase or split phase operation is also possible.

Read more
2193.05 EUR VAT included
The product is in stock
Details

Compara produse

You must add at least one product to compare products.

Was added to wishlist!

Was removed from wishlist!