Your Cart Accessories
Display: 1-15 from 15 products
your selection:
Price: 50,05 - 60,06
- Brand:
Izolatoarele Argo cu diode permit încărcarea simultană a două sau mai multe baterii dintr-un singur alternator, fără a conecta bateriile între ele. De exemplu, descărcarea bateriei de serviciu face ca bateria de pornire să nu se descarce. Căderea de tensiune pe diode este mică, graţie utilizării diodelor Schottky.
- Brand: Victron Energy
- Brand:
Transformator 100A:50mA pentru MultiPlus-II / MultiGrid-II pentru implementarea PowerControl și PowerAssist și pentru optimizarea consumului propriu cu ajutorul senzorului extern de curent.
A se vedea fișa tehnică MultiPlus-II pentru mai multe detalii.
- Brand:
Un cablu pentru conectarea panoului de control al invertorului Phoenix, interfața Victron Energy MK3-USB și conexiuni VE.Bus între multiple dispozitive cu port VE.Bus și GX.
5M ASS030065000
10M ASS030065010
15M ASS030065020
- Brand: Victron Energy
M8 circular connector Male/Female 3 pole cable 2m (bag of 2)
- Brand: Victron Energy
- Brand:
Randament ridicat: Utilizând rectificarea sincronă, randamentul la sarcină maximă depășește 95%.
Protecție IP43: Atunci când este instalat cu bornele cu șurub orientate în jos.
Borne cu șurub: Nu sunt necesare scule speciale pentru instalare.
- Brand: Victron Energy
Current Transformer 100A:50mA for MultiPlus-II / MultiGrid-II to implement PowerControl and PowerAssist and to optimize self-consumption with external current sensing. Maximum current: 32A.
- Brand: Victron Energy
M8 circular connector Male/Female 3 pole cable 3m (bag of 2)
- Brand: Victron Energy
High efficiency
Using synchronous rectification, full load efficiency exceeds 95%.
IP43 protection
When installed with the screw terminals oriented downwards.
Screw terminals
No special tools needed for installation.
Models: 24 Volt
- Brand: Victron Energy
Easily mount a BMV and MPPT Control on a wall.
BMV700 and Color Control in images not included
- Brand: Victron Energy
Diode battery isolators allow simultaneous charging of two or more batteries from one alternator, without connecting the batteries together. Discharging the accessory battery for example will not result in also discharging the starter battery.
The Argo Battery Isolators feature a low voltage drop thanks to the use of Schottky diodes: at low current the voltage drop is approximately 0,3 V and at the rated output approximately 0,45 V.
All models are fitted with a compensation diode that can be used to slightly increase the output voltage of the alternator. This compensates for the voltage drop over the diodes in the isolator.
Simply inserting the isolator in the cabling between the alternator and the batteries will slightly reduce charge voltage. The result can be that batteries are not charged to the full 100% and age prematurely.
Alternator energize input
Some alternators need DC voltage on the B+ output to start charging. Obviously, DC will be present when the alternator is directly connected to a battery. Inserting a Diode or FET splitter will however prevent any return voltage/current from the batteries to the B+, and the alternator will not start.
The new ‘AC’ diode isolators feature a special current limited energize input that will power the B+ when the engine run/stop switch is closed.
- Brand: Victron Energy
Voltage and Temperature sense
Smart Battery Sense is a wireless battery voltage and temperature sensor for Victron MPPT Solar Chargers.
With voltage and temperature sense in place, batteries will be better charged; improving charging-efficiency and prolonging battery life.
Improves battery charging
By measuring voltage at the battery bank terminals, errors arising from voltage-loss due to cable resistance are avoided – guaranteeing the correct charge-voltage.
For lead batteries, battery temperature data is used to adjust the charge-voltages: cold batteries require an increased charge-voltage, whereas hot batteries require a decreased charge-voltage. For lithium batteries temperature data is used to disable charging when they are too cold: charging lithium batteries near or below freezing causes permanent damage to the cells.
Look no wires
The connection between Smart Battery Sense and one or more Solar Charger(s) is wireless: It uses VE.Smart Network – a wireless technology based on Bluetooth Smart.
Information transmitted can be used simultaneously by one, two or more Solar Chargers connected to the same 12V, 24V and 48V battery bank. The Smart Network is set up using the VictronConnect app.
Tidy, simple – smart
Installation is simple, quick and tidy. Just connect the unit’s two eyelets to your battery terminals and attach the Smart Battery Sense unit directly onto the battery-body using its self-adhesive strip.
- Brand: Victron Energy
Using the VE.Direct to Bluetooth Smart dongle you can display your BMV or MPPT information on iOS and Android devices, using the VictronConnect app. View information wirelessly such as battery status and solar panel power, plus other useful data.
The dongle is able to read data from all products with a VE.Direct port, such as the BMV-70x series battery monitors, Phoenix Inverters with VE.Direct port, MPPT Solar Charge Controllers.