Accessories

Display: 1-24 from 79 products

your selection:

Price: Over 203,11 Remove
1
Shunt 2000A/50mV-0,5 / 3xM10
  • Brand: Victron Energy
Description

Shunt 2000A/50mV-0,5 / 3xM10.
Read more
206.67 EUR VAT included
The product is in stock
Details
2
Digital Multi Control 200/200A
  • Brand: Victron Energy

This panel is intended both for Multis and Quattros. It allows PowerControl and PowerAssist current limit setting for two AC sources: a generator and shore side current for example. Setting range: up to 200 Amps. The brightness of the LEDs is automatically reduced during night time.

Read more
212.37 EUR VAT included
The product is in stock
Details
3
Battery Monitor BMV-712 Smart Retail
  • Brand:

Având Bluetooth încorporat, BMV Smart este pregătit pentru era Internetului obiectelor (IoT). Deoarece tehnologia Bluetooth este implementată în majoritatea celorlalte produse Victron Energy, comunicarea fără fir între produse va simplifica instalarea sistemului și va îmbunătăți performanța.

Pentru a citi mai multe despre gama completă și accesoriile BMV, accesați acest blog

Read more
213.20 EUR VAT included
The product is in stock
Details
4
Battery Monitor BMV-712 BLACK Smart Retail
  • Brand:

Având Bluetooth încorporat, BMV Smart este pregătit pentru era Internetului obiectelor (IoT). Deoarece tehnologia Bluetooth este implementată în majoritatea celorlalte produse Victron Energy, comunicarea fără fir între produse va simplifica instalarea sistemului și va îmbunătăți performanța.

Pentru a citi mai multe despre gama completă și accesoriile BMV, accesați acest blog

Read more
213.20 EUR VAT included
The product is in stock
Details
5
Argofet 200-3 Three batteries 200A
  • Brand: Victron Energy

Similarly to diode battery isolators, FET isolators allow simultaneous charging of two or more batteries from one alternator (or a single output battery charger), without connecting the batteries together. Discharging the accessory battery for example will not result in also discharging the starter battery.

In contrast with diode battery isolators, FET isolators have virtually no voltage loss. Voltage drop is less than 0,02 Volt at low current and averages 0,1 Volt at higher currents. When using ARGO FET Battery Isolators, there is no need to also increase the output voltage of the alternator. Care should taken however to keep cable lengths short and of sufficient cross section.

Example:
When a current of 100 A flows through a cable of 50 mm> cross section (AWG 0) and 10 m length (30 ft), the voltage drop over the cable will be 0,26 Volt. Similarly a current of 50 A through a cable of 10 mm> cross section (AWG 7) and 5 m length (15 ft) will result in a voltage drop of 0,35 Volt!

Alternator energize input

Some alternators need DC voltage on the B+ output to start charging. Obviously, DC will be present when the alternator is directly connected to a battery. Inserting a Diode or FET splitter will however prevent any return voltage/current from the batteries to the B+, and the alternator will not start. The new Argofet isolators have a special current limited energize input that will power the B+ when the engine run/stop switch is closed.

Read more
213.80 EUR VAT included
The product is in stock
Details
6
Orion 12/24-20 DC-DC converter IP20
  • Brand: Victron Energy

The Orion-Tr Smart DC-DC charger is a professional DC to DC adaptive 3-stage charger with built-in Bluetooth.

For use in dual battery systems in vehicles or on boats where the (smart) alternator and the start battery are used to charge the service battery. The unit can be monitored and programmed via Bluetooth and can be remotely controlled via a remote on/off switch and has an engine running detection mechanism.

The Orion Tr-Smart charger can be used in 12V or 24V systems and is suitable for both lead acid and lithium batteries. Models are available up to 400W and unlimited multiple units can be connected in parallel to increase output power.

Suitable for high temperatures up to 55°C with a full rated output up to 40°C.

Bluetooth Smart enabled

Any Bluetooth enabled smart phone, tablet or other device can be used to monitor, to change settings and to update the charger when new software features become available.

Fully programmable

– Battery charge algorithm (configurable) or fixed output.
– Smart alternator compatibility: engine running detection mechanism.

Adaptive 3-stage charge algorithm: bulk – absorption – float

  • For lead acid batteries it is important that during shallow discharges the absorption time is kept short in order to prevent overcharging of the battery. After a deep discharge the absorption time is automatically increased to make sure that the battery is completely recharged.
  • For lithium batteries absorption time is fixed, default 2 hours.
  • Alternatively, a fixed output voltage can be chosen.

Remote on-off

A remote on/off switch or relay contact can be connected to a two-pole connector.
Alternatively, the H terminal (right) of the two-pole connector can be switched to battery plus, or the L terminal (left) of the two pole connector can be switched to battery minus (or the chassis of a vehicle, for example).

All models are short circuit proof and can be paralleled to increase output current

An unlimited number of units can be connected in parallel.

High temperature protected

The output current will reduce at high ambient temperature.

Screw terminals

No special tools needed for installation.

Input fuse (not replaceable)

Read more
213.80 EUR VAT included
The product is in stock
Details
7
VE.Net GMDSS panel
  • Brand: Victron Energy
Description

VE.Net GMDSS panel remotely monitors the Victron Skylla-TG GMDSS charger.
Read more
219.10 EUR VAT included
The product is in stock
Details
8
VE.Net Panel (VPN)
  • Brand: Victron Energy
Description

The VE.Net Panel provides a user interface to all connected VE.Net devices. This could be one or more VE.Net Battery Controllers, VE.Net Generator Modules, regular Victron Energy equipment such as inverters and the Multi Inverter/Charger combination, or other third party equipment
Read more
219.10 EUR VAT included
The product is in stock
Details
9
Lynx Power In
  • Brand: Victron Energy
A modular DC bus bar, used to connect batteries to the Lynx DC distribution system.
Read more
225.20 EUR VAT included
The product is in stock
Details
10
VE.Net Blue Power Panel 2
  • Brand: Victron Energy
Description
 

The Blue Power Panel provides intuitive control for all devices connected to the VE.Net network. It can be used to view and configure the full range of settings on VE.Net devices. Furthermore, its fully customizable overview screens make it the ideal monitoring tool for your power system. 

The BPP now features an integrated VE.Net to VE.Bus Converter (VVC). This allows you to combine the powerful control of the VE Configure software with the simple interface of the BPP, without requiring a computer or additional interface devices.

BPP2 and BPC GX

The Blue Power Panel 2 and the Blue Power Control GX almost have the same features. The difference between the two models is the design and the mounting of the panel. The body of the GX panel is made of plastic, which makes the panel lighter and adds a modern look to the panel. An extra advantage of the GX panel is the easy mounting: the included mounting frame allows the user to install the panel from either front or back side. Due to the mounting frame, the mounting holes will no longer be visible.

 
Read more
231.01 EUR VAT included
The product is in stock
Details
11
Smart BatteryProtect 48V-100A
  • Brand: Victron Energy

Protects the battery against excessive discharge and can be used as a system on/off switch

The Smart BatteryProtect disconnects the battery from non-essential loads before it is completely discharged (which would damage the battery) or before it has insufficient power left to crank the engine.
The Smart BatteryProtect can also be used as a system on/off switch. See manual for details.

Bluetooth: programming made easy

When using Bluetooth to program the Smart BatteryProtect any required engage/disengage levels can be set.
Alternatively, one of nine predefined engage/disengage levels can be set with the programming pin (see manual).
If required, Bluetooth can be disabled.

A special setting for Li-ion batteries

In this mode the Battery Protect can be controlled by the VE.Bus BMS.
Note: the BatteryProtect can also be used as a charge interrupter in between a battery charger and a Li-ion battery. See connection
diagram in the manual.

Ultra-low current consumption

This is important in case of Li-ion batteries, especially after low voltage shutdown.
Please see our Li-ion battery datasheet and the VE.Bus BMS manual for more information.

Over voltage protection

To prevent damage to sensitive loads due to over voltage, the load is disconnected whenever the DC voltage exceeds 64V.

Ignition proof

No relays but MOSFET switches, and therefore no sparks.

Delayed alarm output

The alarm output is activated if the battery voltage drops below the preset disconnect level during more than 12 seconds. Starting the engine will therefore not activate the alarm. The alarm output is a short circuit proof open collector output to the negative (minus) rail, max. current 50 mA. The alarm output is typically used to activate a buzzer, LED or relay.

Delayed load disconnect and delayed reconnect

The load will be disconnected 90 seconds after the alarm has been activated. If the battery voltage increases again to the connect threshold within this time period (after the engine has been started for example), the load will not be disconnected.
The load will be reconnected 30 seconds after the battery voltage has increased to more than the preset reconnect voltage.

Read more
232.32 EUR VAT included
The product is in stock
Details
12
Skylla control CE
  • Brand: Victron Energy

The Skylla Control allows you to alter the charge current and see the system status.

Read more
236.60 EUR VAT included
The product is in stock
Details
13
VE.Bus to VE.Can interface
  • Brand: Victron Energy
Description


The VE.Direct to VE.CAN interface cable can be used to make BMV-700 information available on a VE.Can network. Where it can be read by a Color Control GX for example.

Limitations

  • The interface cable does not work with other VE.Direct products, such as Solar Chargers, Inverters and also not with the BMV-712 Smart.
  • When used in combination with a BMV-702 there is limited functionality with regards to the AUX function in the BMV: When used to measure starter battery voltage, that voltage will be transmitted to VE.Can. But when used to measure temperature and or mid-voltage, that data will not be transmitted on the VE.Can network.
Read more
238.16 EUR VAT included
The product is in stock
Details
14
Cyrix-Li-load 12/24V-230A intelligent load relay
  • Brand: Victron Energy
Description

The Cyrix-Li-load will disengage when its control input becomes free floating. If the battery voltage recovers after disconnection (which will happen when no other loads are connected to the battery), the output of the BMS will become high and the Cyrix will reengage after 30 seconds. After 3 attempts to reengage, the Cyrix will remain disengaged until battery voltage has increased to more than 13 V (resp. 26 V or 52 V) during at least 30 seconds (which is a sign that the battery is being recharged). Alternatively, a BatteryProtect can be used (advantage: very low power consumption).
Read more
246.58 EUR VAT included
The product is in stock
Details
15
Cyrix-Li-load 24/48V-230A intelligent charge relay
  • Brand: Victron Energy
Description

The Cyrix-Li-load will disengage when its control input becomes free floating. If the battery voltage recovers after disconnection (which will happen when no other loads are connected to the battery), the output of the BMS will become high and the Cyrix will reengage after 30 seconds. After 3 attempts to reengage, the Cyrix will remain disengaged until battery voltage has increased to more than 13 V (resp. 26 V or 52 V) during at least 30 seconds (which is a sign that the battery is being recharged). Alternatively, a BatteryProtect can be used (advantage: very low power consumption)
Read more
246.58 EUR VAT included
The product is in stock
Details
16
Cyrix-Li-charge 12/24V-230A intelligent charge relay
  • Brand: Victron Energy

The LiFePO4 battery: preventing cell under voltage, overvoltage and over temperature

The first line of protection is cell balancing. All Victron LiFePO4 batteries have integrated cell balancing.
The second line of protection consists of:
– shut down of the load in case of imminent cell under voltage, and
– shut down or reduction of the charging current in case of imminent cell over voltage, high temperature
(>50°C) or low temperature (<0°C).
The VE.Bus BMS is the core of the second protection line.
However, not all loads or chargers can be controlled directly by the VE.Bus BMS.
In order to shut down such loads or chargers several VE.Bus BMS controllable Cyrix switches are available.

Cyrix-Li-load

The Cyrix-Li-load will disengage when its control input becomes free floating.
If the battery voltage recovers after disconnection (which will happen when no other loads are connected to the battery), the output of the BMS will become high and the Cyrix will reengage after 30 seconds. After 3 attempts to reengage, the Cyrix will remain disengaged until battery voltage has increased to more than 13 V (resp. 26 V or 52 V) during at least 30 seconds (which is a sign that the battery is being recharged).
Alternatively, a BatteryProtect can be used (advantage: very low power consumption).

Cyrix-Li-Charge

The Cyrix-Li-Charge will connect a battery charger with 3 seconds delay:
– if the charge disconnect output of the VE.Bus BMS is high, and
– if it senses 13,7 V (resp. 27,4 V or 54,8 V) or more on its battery charger connection terminal, and
– if it senses 2 V or more on its battery terminal (the Cyrix will remain open if not connect to the battery).
The Cyrix-Li-Charge will disengage immediately whenever its control input becomes free floating, signalling cell over
voltage or cell over temperature.
In general a cell over voltage alarm will reset shortly after charging has been stopped. The Cyrix will then reconnect the charger after a delay 3 seconds. After 2 attempts to reengage with 3 seconds delay, the delay increases to 10 minutes.
Whenever battery voltage is less than 13,5 V (resp. 27 V or 54 V), the Cyrix will disengage with a delay of 1 hour.
Note 1: In case of zero discharge current, or a small discharge current, the Cyrix will not disengage shortly after the
charger has been switched off and/or disconnected, because battery voltage will remain higher than 13,5 V.
Note 2: If, after the Cyrix has disengaged, the output of the battery charger immediately increases to 13,7 V or more, the
Cyrix will reengage, with 3 seconds delay.

Cyrix-Li-ct

The functionality of the Cyrix-Li-ct is analogous to the Cyrix-ct.
The Cyrix-Li-ct will parallel connect a lead acid starter battery and a LiFePO4 battery:
– if the charge disconnect output of the VE.Bus BMS is high, and
– if it senses 13,4 V (resp. 26,8 V) or more on one of its power terminals.
The Cyrix will disengage immediately:
– when its control output becomes free floating, signalling cell over voltage or cell over temperature, and/or
– when battery voltage drops below 13,2 V.
Start assist function: a short positive pulse will close the relay during 30 seconds (see figure on page 2).
A built-in transient voltage suppressor will limit the voltage spike that may occur when the Cyrix suddenly disengages due to cell overvoltage or over temperature.

LED status indication

LED on: engaged LED 10 s flash: disengaged
LED 2 s flash: connecting LED 2 s blink: disconnecting
LED 0,25 s blink: alarm (over temperature; voltage > 16 V; both batteries < 10 V; one battery < 2 V)
(multiply by two for 24 V)

Read more
246.58 EUR VAT included
The product is in stock
Details
17
Cyrix-Li-charge 24/48V-230A intelligent charge relay
  • Brand: Victron Energy

The LiFePO4 battery: preventing cell under voltage, overvoltage and over temperature

The first line of protection is cell balancing. All Victron LiFePO4 batteries have integrated cell balancing.
The second line of protection consists of:
– shut down of the load in case of imminent cell under voltage, and
– shut down or reduction of the charging current in case of imminent cell over voltage, high temperature
(>50°C) or low temperature (<0°C).
The VE.Bus BMS is the core of the second protection line.
However, not all loads or chargers can be controlled directly by the VE.Bus BMS.
In order to shut down such loads or chargers several VE.Bus BMS controllable Cyrix switches are available.

Cyrix-Li-load

The Cyrix-Li-load will disengage when its control input becomes free floating.
If the battery voltage recovers after disconnection (which will happen when no other loads are connected to the battery), the output of the BMS will become high and the Cyrix will reengage after 30 seconds. After 3 attempts to reengage, the Cyrix will remain disengaged until battery voltage has increased to more than 13 V (resp. 26 V or 52 V) during at least 30 seconds (which is a sign that the battery is being recharged).
Alternatively, a BatteryProtect can be used (advantage: very low power consumption).

Cyrix-Li-Charge

The Cyrix-Li-Charge will connect a battery charger with 3 seconds delay:
– if the charge disconnect output of the VE.Bus BMS is high, and
– if it senses 13,7 V (resp. 27,4 V or 54,8 V) or more on its battery charger connection terminal, and
– if it senses 2 V or more on its battery terminal (the Cyrix will remain open if not connect to the battery).
The Cyrix-Li-Charge will disengage immediately whenever its control input becomes free floating, signalling cell over
voltage or cell over temperature.
In general a cell over voltage alarm will reset shortly after charging has been stopped. The Cyrix will then reconnect the charger after a delay 3 seconds. After 2 attempts to reengage with 3 seconds delay, the delay increases to 10 minutes.
Whenever battery voltage is less than 13,5 V (resp. 27 V or 54 V), the Cyrix will disengage with a delay of 1 hour.
Note 1: In case of zero discharge current, or a small discharge current, the Cyrix will not disengage shortly after the
charger has been switched off and/or disconnected, because battery voltage will remain higher than 13,5 V.
Note 2: If, after the Cyrix has disengaged, the output of the battery charger immediately increases to 13,7 V or more, the
Cyrix will reengage, with 3 seconds delay.

Cyrix-Li-ct

The functionality of the Cyrix-Li-ct is analogous to the Cyrix-ct.
The Cyrix-Li-ct will parallel connect a lead acid starter battery and a LiFePO4 battery:
– if the charge disconnect output of the VE.Bus BMS is high, and
– if it senses 13,4 V (resp. 26,8 V) or more on one of its power terminals.
The Cyrix will disengage immediately:
– when its control output becomes free floating, signalling cell over voltage or cell over temperature, and/or
– when battery voltage drops below 13,2 V.
Start assist function: a short positive pulse will close the relay during 30 seconds (see figure on page 2).
A built-in transient voltage suppressor will limit the voltage spike that may occur when the Cyrix suddenly disengages due to cell overvoltage or over temperature.

LED status indication

LED on: engaged LED 10 s flash: disengaged
LED 2 s flash: connecting LED 2 s blink: disconnecting
LED 0,25 s blink: alarm (over temperature; voltage > 16 V; both batteries < 10 V; one battery < 2 V)
(multiply by two for 24 V)

Read more
246.58 EUR VAT included
The product is in stock
Details
18
Cyrix-Li-ct 12/24V-230A intelligent Li-ion battery combiner
  • Brand: Victron Energy

The LiFePO4 battery: preventing cell under voltage, overvoltage and over temperature

The first line of protection is cell balancing. All Victron LiFePO4 batteries have integrated cell balancing.
The second line of protection consists of:
– shut down of the load in case of imminent cell under voltage, and
– shut down or reduction of the charging current in case of imminent cell over voltage, high temperature
(>50°C) or low temperature (<0°C).
The VE.Bus BMS is the core of the second protection line.
However, not all loads or chargers can be controlled directly by the VE.Bus BMS.
In order to shut down such loads or chargers several VE.Bus BMS controllable Cyrix switches are available.

Cyrix-Li-load

The Cyrix-Li-load will disengage when its control input becomes free floating.
If the battery voltage recovers after disconnection (which will happen when no other loads are connected to the battery), the output of the BMS will become high and the Cyrix will reengage after 30 seconds. After 3 attempts to reengage, the Cyrix will remain disengaged until battery voltage has increased to more than 13 V (resp. 26 V or 52 V) during at least 30 seconds (which is a sign that the battery is being recharged).
Alternatively, a BatteryProtect can be used (advantage: very low power consumption).

Cyrix-Li-Charge

The Cyrix-Li-Charge will connect a battery charger with 3 seconds delay:
– if the charge disconnect output of the VE.Bus BMS is high, and
– if it senses 13,7 V (resp. 27,4 V or 54,8 V) or more on its battery charger connection terminal, and
– if it senses 2 V or more on its battery terminal (the Cyrix will remain open if not connect to the battery).
The Cyrix-Li-Charge will disengage immediately whenever its control input becomes free floating, signalling cell over
voltage or cell over temperature.
In general a cell over voltage alarm will reset shortly after charging has been stopped. The Cyrix will then reconnect the charger after a delay 3 seconds. After 2 attempts to reengage with 3 seconds delay, the delay increases to 10 minutes.
Whenever battery voltage is less than 13,5 V (resp. 27 V or 54 V), the Cyrix will disengage with a delay of 1 hour.
Note 1: In case of zero discharge current, or a small discharge current, the Cyrix will not disengage shortly after the
charger has been switched off and/or disconnected, because battery voltage will remain higher than 13,5 V.
Note 2: If, after the Cyrix has disengaged, the output of the battery charger immediately increases to 13,7 V or more, the
Cyrix will reengage, with 3 seconds delay.

Cyrix-Li-ct

The functionality of the Cyrix-Li-ct is analogous to the Cyrix-ct.
The Cyrix-Li-ct will parallel connect a lead acid starter battery and a LiFePO4 battery:
– if the charge disconnect output of the VE.Bus BMS is high, and
– if it senses 13,4 V (resp. 26,8 V) or more on one of its power terminals.
The Cyrix will disengage immediately:
– when its control output becomes free floating, signalling cell over voltage or cell over temperature, and/or
– when battery voltage drops below 13,2 V.
Start assist function: a short positive pulse will close the relay during 30 seconds (see figure on page 2).
A built-in transient voltage suppressor will limit the voltage spike that may occur when the Cyrix suddenly disengages due to cell overvoltage or over temperature.

LED status indication

LED on: engaged LED 10 s flash: disengaged
LED 2 s flash: connecting LED 2 s blink: disconnecting
LED 0,25 s blink: alarm (over temperature; voltage > 16 V; both batteries < 10 V; one battery < 2 V)
(multiply by two for 24 V)

Read more
246.58 EUR VAT included
The product is in stock
Details
19
SmartShunt 1000A/50mV IP65
  • Brand:

The SmartShunt este un monitor de baterie complet, doar că fără un ecran. Telefonul dvs. acționează ca un ecran. The SmartShunt se conectează prin Bluetooth la aplicația VictronConnect de pe telefonul (sau tableta) dvs., și puteți citi în mod convenabil toți parametrii monitorizați ai bateriei, precum nivelul de încărcare, timpul rămas, informații istorice și mult mai multe.

Alternativ, SmartShunt poate fi conectat și citit de un dispozitiv GX. Conexiunea la SmartShunt se realizează printr-un cablu VE.Direct.

SmartShunt este o alternativă bună pentru un monitor de baterie BMV, în special pentru sisteme unde este necesară monitorizarea bateriei, dar se doresc mai puține cabluri și dezordine.
SmartShunt este dotat cu Bluetooth, un port VE.Direct și o conexiune care poate fi utilizată pentru: monitorizarea unei baterii suplimentare, monitorizare mediană sau senzor de temperatură.

Read more
247.93 EUR VAT included
The product is in stock
Details
20
Smart BMS CL 12-100
  • Brand: Victron Energy

The Smart BMS CL 12/100 is a Battery Management system for Victron lithium-iron-phosphate (LiFePO4) Smart Batteries. It has been specifically designed for 12V systems with a 12V alternator.

The BMS CL 12/100 monitors and protects each individual battery cell within the battery (or battery bank) and will disconnect the alternator, charge sources or DC loads in case of low battery voltage, high battery voltage or over temperature.

The dedicated alternator input provides current limiting and one-way traffic from the alternator into the battery, this so any size alternator (and start battery) can be safely connected to the Smart Lithium battery or batteries.

The BMS is also equipped with a remote on off connector, to turn the BMS (and the system) off via a remote switch, and a pre-alarm contact, to give a warning signal before the BMS will disconnect the batteries from the system.

Read more
255.14 EUR VAT included
The product is in stock
Details
21
Shore Power Cord 15m 16A/250Vac (3x2,5sqmm)
  • Brand: Victron Energy

Remote on-off
The remote on-off eliminates the need for a high current switch in the input wiring. The remote on-off can be operated with a low power switch or by for example the engine run/stop switch (see manual). 

Adjustable output voltage: can also be used as a battery charger
For example to charge a 12 Volt starter or accessory battery in an otherwise 24V system. 

All models are short circuit proof and can be paralleled to increase output current
An unlimited number of units can be connected in parallel. 

IP43 protection
When installed with the screw terminals oriented downwards. 

Screw terminals
No special tools needed for installation.

Input fuse
On 12V and 24V input models only.

Read more
255.14 EUR VAT included
The product is in stock
Details
22
VE.Direct to NMEA2000 interface
  • Brand: Victron Energy
Description

This NMEA2000 drop cable makes the BMV-700 information available to an NMEA2000 networks. Battery information such as voltage, current and state of charge can be displayed on common purpose displays from other manufacturers which accept the NMEA2000 data being sent.

Limitations:

  • The cable does not work with other VE.Direct products, such as Solar Chargers, Inverters and also not with the BMV-712 Smart.
  • When used in combination with a BMV-702 there is limited functionality with regards to the AUX function in the BMV: When used to measure starter battery voltage, that voltage will be transmitted to the NMEA2000 network. But when used to measure temperature and or mid-voltage, that data will not be transmitted on the NMEA2000 network.
Read more
260.78 EUR VAT included
The product is in stock
Details
23
GlobalLink 520
  • Brand:

Credem că a avea o înțelegere asupra instalației dvs. este un factor cheie în menținerea și operarea soluțiilor dvs. de energie în afara rețelei. In afara rețelei nu ar trebui să însemne off-line(deconectat), așa că am creat GlobalLink 520. Acest dispozitiv va aduce conectivitate 4G LTE-M la toate dispozitivele activate VE.Direct fără taxe lunare sau abonamente, în primii cinci ani. 

Read more
276.68 EUR VAT included
The product is in stock
Details
24
Cerbo-S GX
  • Brand:

Acest centru complet nou de comunicare vă permite să aveți întotdeauna control perfect asupra sistemului dvs., de oriunde vă aflați, și maximizează performanța acestuia. Tot ce trebuie să faceți este să vă conectați la portalul nostru Victron Remote Management - Acces la distanță Victron (VRM), sau accesați direct utilizând GX Touch separat, un MFD sau aplicația noastră VictronConnect, datorită capabilității sale adăugate Bluetooth. Ultima adiție la gama GX combină ce este mai bun din conectivitate, redefinind soluțiile de alimentare inteligentă în fiecare metodă.

Uita-te la noul video care explică tot ce poate fi cunoscut despre instalarea noului Cerbo GX & GX Touch 50.


Read more
277.87 EUR VAT included
The product is in stock
Details

Compara produse

You must add at least one product to compare products.

Was added to wishlist!

Was removed from wishlist!