Accessories

Display: 1-24 from 34 products

your selection:

Price: 149,61 - 199,48 Remove
1
Zigbee to USB converter
  • Brand: Victron Energy

Zigbee to RS485 converter, DRF2658C, DTK.

Read more
149.65 EUR VAT included
The product is in stock
Details
2
SmartShunt 500A/50mV IP65
  • Brand:

The SmartShunt este un monitor de baterie complet, doar că fără un ecran. Telefonul dvs. acționează ca un ecran. The SmartShunt se conectează prin Bluetooth la aplicația VictronConnect de pe telefonul (sau tableta) dvs., și puteți citi în mod convenabil toți parametrii monitorizați ai bateriei, precum nivelul de încărcare, timpul rămas, informații istorice și mult mai multe.

Alternativ, SmartShunt poate fi conectat și citit de un dispozitiv GX. Conexiunea la SmartShunt se realizează printr-un cablu VE.Direct.

SmartShunt este o alternativă bună pentru un monitor de baterie BMV, în special pentru sisteme unde este necesară monitorizarea bateriei, dar se doresc mai puține cabluri și dezordine.
SmartShunt este dotat cu Bluetooth, un port VE.Direct și o conexiune care poate fi utilizată pentru: monitorizarea unei baterii suplimentare, monitorizare mediană sau senzor de temperatură.

Read more
149.72 EUR VAT included
The product is in stock
Details
3
Argofet 100-2 Two batteries 100A
  • Brand: Victron Energy

Similarly to diode battery isolators, FET isolators allow simultaneous charging of two or more batteries from one alternator (or a single output battery charger), without connecting the batteries together. Discharging the accessory battery for example will not result in also discharging the starter battery.

In contrast with diode battery isolators, FET isolators have virtually no voltage loss. Voltage drop is less than 0,02 Volt at low current and averages 0,1 Volt at higher currents. When using ARGO FET Battery Isolators, there is no need to also increase the output voltage of the alternator. Care should taken however to keep cable lengths short and of sufficient cross section.

Example:
When a current of 100 A flows through a cable of 50 mm> cross section (AWG 0) and 10 m length (30 ft), the voltage drop over the cable will be 0,26 Volt. Similarly a current of 50 A through a cable of 10 mm> cross section (AWG 7) and 5 m length (15 ft) will result in a voltage drop of 0,35 Volt!

Alternator energize input

Some alternators need DC voltage on the B+ output to start charging. Obviously, DC will be present when the alternator is directly connected to a battery. Inserting a Diode or FET splitter will however prevent any return voltage/current from the batteries to the B+, and the alternator will not start. The new Argofet isolators have a special current limited energize input that will power the B+ when the engine run/stop switch is closed.

Read more
152.51 EUR VAT included
The product is in stock
Details
4
Argofet 200-2 Two batteries 200A Retail
  • Brand:

Similare izolatoarelor cu diode, izolatoarele Argofet permit încărcarea simultană a două sau mai multe baterii de la un singur alternator (sau de la singur încărcător) fără a conecta bateriile între ele. În comparaţie cu izolatoarele cu diode, izolatoarele Argofet au avantajul unei căderi de tensiune aproape nulă. Căderea de tensiune este de mai puţin de 0,02 volţi la un curent mic şi în medie de 0,1 volţi pentru un curent mare.

Read more
153.31 EUR VAT included
The product is in stock
Details
5
Plug 32A/250Vac (2p/3w) for Power Inlet stainless steel 32A
  • Brand: Victron Energy

Plug 32A/250Vac (2p/3w) for Power Inlet stainless steel 32A

 
Read more
153.94 EUR VAT included
The product is in stock
Details
6
Cyrix-ct 12/24V-230A intelligent battery combiner Retail
  • Brand:

Combinatorul de baterii Cyrix este un releu foarte rezistent controlat printr-un microprocesor, care conectează în mod automat bateriile în paralel, atunci când una dintre ele a atins nivelul de tensiune prestabilit (ceea ce indică faptul că bateria este încărcată) şi se deconectează atunci când tensiunea bateriei este sub nivelul fixat (ceea ce indică faptul că una sau mai multe baterii sunt descărcate). Combinatorii de baterii Cyrix reprezintă un excelent substitut pentru izolatorii cu diode. Principala caracteristică este aceea că, practic, nu există vreo cădere de tensiune, astfel încât tensiunea furnizată de alternator sau de încărcătorul de baterii nu trebuie să fie mai mare.

Read more
154.51 EUR VAT included
The product is in stock
Details
7
SHS 200 MPPT v3.0
  • Brand: Victron Energy
Description

The SHS 200 is a smart solar charge controller and power distribution system designed for off-grid electricity access. It is used with solar panels and a battery to power DC appliances (12V). Low-cost and reliable offline Pay-as-you-go (PAYGo) operations are possible through keypad activation.

Modular solar home system

The SHS 200 is compatible with different size of batteries (up to 12V/160Ah) and solar panels (up to 200Wp). End-users can progressively increase their power subscription according to their needs and budget. With eleven DC load outputs, the SHS 200 can be connected to a variety of household appliances such LED lighting, phone charging, fans, TVs and a fridge. This solution is also powerful enough for entrepreneurial customers to run a small business.

PAYGo ready

The SHS 200 is primarily designed for Pay-as-you-go (PAYGo) operations. It is compatible with various PAYGo software platforms and includes a keypad for offline activation. How does it work? PAYGo operators usually offer solar home systems to their customers through a rent-to-own plan on prepayments. Customers can get a SHS 200 against a deposit. Then they make regular payments by mobile money over few months or years to finally own the unit. A recharge code is sent to their cell phone by SMS after each payment. The SHS 200 becomes active only when the code is pressed on its keypad. PAYGo operators can achieve profitability while off-grid populations afford reliable and clean energy.

MPPT charger and smart battery management

By using Maximum Power Point Tracking (MPPT) technology, the SHS 200 ensures that every drop of available power is rinsed out of the panels and harvested for storage. Additionally smart multi-stage charging and load disconnect features maintain the health and extends the life of the battery. The SHS 200 is compatible with lead-acid and lithium battery technologies.

 

Features

200W MPPT charge controller

Smart charge controller with four PV inputs of 50Wp. Maximum power point tracking (MPPT) will improve energy harvest by up to 30% compared to PWM charge controllers.

Smart battery management

Smart multi-stage charging and load disconnect to extend battery life. Internal temperature sensor (compensates charge voltage according to temperature). Optional battery cap to prevent user from tampering with battery terminals.

Fifteen DC load outputs

Compatible with large range of accessories such as LED lighting, mobile phone charging, TVs, DC fridge, fans or sound systems.

Read more
154.80 EUR VAT included
The product is in stock
Details
8
Power Inlet stainless steel with cover 32A/250Vac (2p/3w)
  • Brand:

• Cablu cu protecţie la pătrunderea apei, cu conexiune IP56
• Conector şi fişă turnate etanş
• LED ce indică prezenţa tensiunii
• Capac de protecţie 
• Conexiune din oţel inoxidabil Disponibil în: 15M 16A 25M 16A 15M 25A 25M 25A

Read more
156.90 EUR VAT included
The product is in stock
Details
9
Digital Multi Control 200/200A GX (Right Angle RJ45) Retail
  • Brand:

Digital Multi Control este folosit pentru a vizualiza și regla de la distanță curenții de intrare CA, pentru a porni și opri Multi sau Quattro. Este conceput pentru a se integra curat cu panoul de control al sistemului bărcii, vehicululul sau casei dumneavoastră.

Panoul Digital Multi Control (DMC) este proiectat să funcționeze cu toate tipurile de Multi/Quattro. Aceasta include configurații de sine stătătoare, paralele și 2-3 faze. Conectarea DMC la sistemul dvs. este simplă, în cele mai multe cazuri doar conectarea DMC cu un cablu RJ45 este suficientă și nu este necesară o manipulare suplimentară. 


Read more
158.10 EUR VAT included
The product is in stock
Details
10
VE.Net Tank Monitor (Resistive)
  • Brand: Victron Energy

The VE.Net Tank Sensor, when used with appropriate tank senders, can be used to monitor the amount of liquid in up to three tanks, such as a water or diesel tank.

VE.Net stands for Victron Energy Network. It allows all VE.Net compatible devices to communicate with each other. This means that the charger, for example, can get information from the battery monitor to optimize the charge current. It is possible to control and monitor all your VE.Net devices from a single VE.Net compatible control panel. This saves space and allows you to control all your devices from one place. A VE.Net consists of a VE.Net panel (VPN), and one or more other VE.Net devices, such as the VE.Net Tank Sensor or VE.Net Battery Controller.

To install your tank sensor you will need:

1.Standard supplied cable including inline fuse holder with a 1Amp slow blow fuse (voltage and current models only).

2.One Cat5 cable with two RJ45 connectors (to connect a VE.Net Panel or other VE.Net devices) available in 5, 10, 15, 20, 25 and 30 meters.

3.Wires for connecting the senders (refer to the sender manual for more information).

Read more
161.94 EUR VAT included
The product is in stock
Details
11
Skylla-i Control GX (Right Angle RJ45) Retail
  • Brand:
Skylla-i Control vă permite să modificați curentul de încărcare și să vedeți starea sistemului.
Read more
166.49 EUR VAT included
The product is in stock
Details
12
Galvanic Isolator VDI-16 A
  • Brand: Victron Energy

The galvanic isolator prevents electrolytic corrosion. It blocks low voltage DC currents that enter your boat via the shore power earth wire. These currents can cause corrosion to the boat’s underwater metals, like the hull, propeller, shaft and so on.

The galvanic isolator consists internally of two diodes which are connected in anti-parallel fashion. When they are connected in this way, the diodes allow current in both directions but only above a certain threshold voltage. The voltage at which diodes conduct is about 1.4 Vdc.

The isolator is installed directly behind your boat’s 230V connection. The forward voltage from the galvanic isolator is higher than the potential difference between metals. As a result, this voltage will not allow conduction and as such, the galvanic isolator will prevent any electrolytic current. However, if there is a (higher) error voltage in the AC circuit, the diodes will allow current through and the residual-current device will break the circuit.

Read more
166.75 EUR VAT included
The product is in stock
Details
13
Argodiode 180-3AC 3 batteries 180A
  • Brand: Victron Energy

Diode battery isolators allow simultaneous charging of two or more batteries from one alternator, without connecting the batteries together. Discharging the accessory battery for example will not result in also discharging the starter battery.

The Argo Battery Isolators feature a low voltage drop thanks to the use of Schottky diodes: at low current the voltage drop is approximately 0,3 V and at the rated output approximately 0,45 V.

All models are fitted with a compensation diode that can be used to slightly increase the output voltage of the alternator. This compensates for the voltage drop over the diodes in the isolator.

Simply inserting the isolator in the cabling between the alternator and the batteries will slightly reduce charge voltage. The result can be that batteries are not charged to the full 100% and age prematurely.

Alternator energize input

Some alternators need DC voltage on the B+ output to start charging. Obviously, DC will be present when the alternator is directly connected to a battery. Inserting a Diode or FET splitter will however prevent any return voltage/current from the batteries to the B+, and the alternator will not start.

The new ‘AC’ diode isolators feature a special current limited energize input that will power the B+ when the engine run/stop switch is closed.

Read more
166.75 EUR VAT included
The product is in stock
Details
14
Zigbee to RS485 converter
  • Brand: Victron Energy

Zigbee to USB converter, DRF2618A, DTK.

Read more
172.47 EUR VAT included
The product is in stock
Details
15
Orion-Tr 12/12-18A (220W) Isolated DC-DC converter
  • Brand: Victron Energy

Remote on-off

The remote on-off eliminates the need for a high current switch in the input wiring. The remote on-off can be operated with a low power switch or by for example the engine run/stop switch (see manual).

Adjustable output voltage: can also be used as a battery charger

For example to charge a 12 Volt starter or accessory battery in an otherwise 24V system.

All models are short circuit proof and can be paralleled to increase output current

An unlimited number of units can be connected in parallel.

High temperature protected

The output current will reduce at high ambient temperature.

IP43 protection

When installed with the screw terminals oriented downwards.

Screw terminals

No special tools needed for installation.

Input fuse (not replaceable)

On 12V and 24V input models only.

Models: 12 / 24 / 48 Volt

Read more
173.88 EUR VAT included
The product is in stock
Details
16
Orion-Tr 12/24-10A (240W) Isolated DC-DC converter
  • Brand: Victron Energy

Remote on-off

The remote on-off eliminates the need for a high current switch in the input wiring. The remote on-off can be operated with a low power switch or by for example the engine run/stop switch (see manual).

Adjustable output voltage: can also be used as a battery charger

For example to charge a 12 Volt starter or accessory battery in an otherwise 24V system.

All models are short circuit proof and can be paralleled to increase output current

An unlimited number of units can be connected in parallel.

High temperature protected

The output current will reduce at high ambient temperature.

IP43 protection

When installed with the screw terminals oriented downwards.

Screw terminals

No special tools needed for installation.

Input fuse (not replaceable)

On 12V and 24V input models only.

Models: 12 / 24 / 48 Volt

Read more
173.88 EUR VAT included
The product is in stock
Details
17
Orion-Tr 24/12-20A (240W) Isolated DC-DC converter
  • Brand: Victron Energy

Remote on-off

The remote on-off eliminates the need for a high current switch in the input wiring. The remote on-off can be operated with a low power switch or by for example the engine run/stop switch (see manual).

Adjustable output voltage: can also be used as a battery charger

For example to charge a 12 Volt starter or accessory battery in an otherwise 24V system.

All models are short circuit proof and can be paralleled to increase output current

An unlimited number of units can be connected in parallel.

High temperature protected

The output current will reduce at high ambient temperature.

IP43 protection

When installed with the screw terminals oriented downwards.

Screw terminals

No special tools needed for installation.

Input fuse (not replaceable)

On 12V and 24V input models only.

Models: 12 / 24 / 48 Volt

Read more
173.88 EUR VAT included
The product is in stock
Details
18
Orion-Tr 24/24-12A (280W) Isolated DC-DC converter
  • Brand: Victron Energy

Remote on-off

The remote on-off eliminates the need for a high current switch in the input wiring. The remote on-off can be operated with a low power switch or by for example the engine run/stop switch (see manual).

Adjustable output voltage: can also be used as a battery charger

For example to charge a 12 Volt starter or accessory battery in an otherwise 24V system.

All models are short circuit proof and can be paralleled to increase output current

An unlimited number of units can be connected in parallel.

High temperature protected

The output current will reduce at high ambient temperature.

IP43 protection

When installed with the screw terminals oriented downwards.

Screw terminals

No special tools needed for installation.

Input fuse (not replaceable)

On 12V and 24V input models only.

Models: 12 / 24 / 48 Volt

Read more
173.88 EUR VAT included
The product is in stock
Details
19
Orion-Tr 24/48-6A (280W) Isolated DC-DC converter
  • Brand: Victron Energy

Remote on-off

The remote on-off eliminates the need for a high current switch in the input wiring. The remote on-off can be operated with a low power switch or by for example the engine run/stop switch (see manual).

Adjustable output voltage: can also be used as a battery charger

For example to charge a 12 Volt starter or accessory battery in an otherwise 24V system.

All models are short circuit proof and can be paralleled to increase output current

An unlimited number of units can be connected in parallel.

High temperature protected

The output current will reduce at high ambient temperature.

IP43 protection

When installed with the screw terminals oriented downwards.

Screw terminals

No special tools needed for installation.

Input fuse (not replaceable)

On 12V and 24V input models only.

Models: 12 / 24 / 48 Volt

Read more
173.88 EUR VAT included
The product is in stock
Details
20
Orion-Tr 48/12-20A (240W) Isolated DC-DC converter
  • Brand: Victron Energy

Remote on-off

The remote on-off eliminates the need for a high current switch in the input wiring. The remote on-off can be operated with a low power switch or by for example the engine run/stop switch (see manual).

Adjustable output voltage: can also be used as a battery charger

For example to charge a 12 Volt starter or accessory battery in an otherwise 24V system.

All models are short circuit proof and can be paralleled to increase output current

An unlimited number of units can be connected in parallel.

High temperature protected

The output current will reduce at high ambient temperature.

IP43 protection

When installed with the screw terminals oriented downwards.

Screw terminals

No special tools needed for installation.

Input fuse (not replaceable)

On 12V and 24V input models only.

Models: 12 / 24 / 48 Volt

Read more
173.88 EUR VAT included
The product is in stock
Details
21
Orion-Tr 48/24-12A (280W) Isolated DC-DC converter
  • Brand: Victron Energy

Remote on-off

The remote on-off eliminates the need for a high current switch in the input wiring. The remote on-off can be operated with a low power switch or by for example the engine run/stop switch (see manual).

Adjustable output voltage: can also be used as a battery charger

For example to charge a 12 Volt starter or accessory battery in an otherwise 24V system.

All models are short circuit proof and can be paralleled to increase output current

An unlimited number of units can be connected in parallel.

High temperature protected

The output current will reduce at high ambient temperature.

IP43 protection

When installed with the screw terminals oriented downwards.

Screw terminals

No special tools needed for installation.

Input fuse (not replaceable)

On 12V and 24V input models only.

Models: 12 / 24 / 48 Volt

Read more
173.88 EUR VAT included
The product is in stock
Details
22
Orion-Tr 48/48-6A (280W) Isolated DC-DC converter
  • Brand: Victron Energy

Remote on-off

The remote on-off eliminates the need for a high current switch in the input wiring. The remote on-off can be operated with a low power switch or by for example the engine run/stop switch (see manual).

Adjustable output voltage: can also be used as a battery charger

For example to charge a 12 Volt starter or accessory battery in an otherwise 24V system.

All models are short circuit proof and can be paralleled to increase output current

An unlimited number of units can be connected in parallel.

High temperature protected

The output current will reduce at high ambient temperature.

IP43 protection

When installed with the screw terminals oriented downwards.

Screw terminals

No special tools needed for installation.

Input fuse (not replaceable)

On 12V and 24V input models only.

Models: 12 / 24 / 48 Volt

Read more
173.88 EUR VAT included
The product is in stock
Details
23
Argofet 100-3 Three batteries 100A
  • Brand: Victron Energy

Similarly to diode battery isolators, FET isolators allow simultaneous charging of two or more batteries from one alternator (or a single output battery charger), without connecting the batteries together. Discharging the accessory battery for example will not result in also discharging the starter battery.

In contrast with diode battery isolators, FET isolators have virtually no voltage loss. Voltage drop is less than 0,02 Volt at low current and averages 0,1 Volt at higher currents. When using ARGO FET Battery Isolators, there is no need to also increase the output voltage of the alternator. Care should taken however to keep cable lengths short and of sufficient cross section.

Example:
When a current of 100 A flows through a cable of 50 mm> cross section (AWG 0) and 10 m length (30 ft), the voltage drop over the cable will be 0,26 Volt. Similarly a current of 50 A through a cable of 10 mm> cross section (AWG 7) and 5 m length (15 ft) will result in a voltage drop of 0,35 Volt!

Alternator energize input

Some alternators need DC voltage on the B+ output to start charging. Obviously, DC will be present when the alternator is directly connected to a battery. Inserting a Diode or FET splitter will however prevent any return voltage/current from the batteries to the B+, and the alternator will not start. The new Argofet isolators have a special current limited energize input that will power the B+ when the engine run/stop switch is closed.

Read more
175.31 EUR VAT included
The product is in stock
Details
24
Smart BatteryProtect 12/24V-220A
  • Brand: Victron Energy

Protects the battery against excessive discharge and can be used as a system on/off switch

The Smart BatteryProtect disconnects the battery from non-essential loads before it is completely discharged (which would damage the battery) or before it has insufficient power left to crank the engine.
The on/off input can be used as a system on/off switch.

12/24V auto ranging

The Smart BatteryProtect automatically detects system voltage one time only.

Bluetooth: programming made easy

When using Bluetooth to program the Smart BatteryProtect any required engage/disengage levels can be set.
Alternatively, one of nine predefined engage/disengage levels can be set with the programming pin (see manual).
If required, Bluetooth can be disabled.

A special setting for Li-ion batteries

In this mode the BatteryProtect can be controlled by the VE.Bus BMS.
Note: the BatteryProtect can also be used as a charge interrupter in between a battery charger and a Li-ion battery. See connection diagram in the manual.

Ultra-low current consumption

This is important in case of Li-ion batteries, especially after low voltage shutdown.
Please see our Li-ion battery datasheet and the VE.Bus BMS manual for more information.

Over voltage protection

To prevent damage to sensitive loads due to over voltage, the load is disconnected whenever the DC voltage exceeds 16.3V respectively 32.6V.

Ignition proof

No relays but MOSFET switches, and therefore no sparks.

Delayed alarm output

The alarm output is activated if the battery voltage drops below the preset disconnect level during more than 12 seconds.
Starting the engine will therefore not activate the alarm. The alarm output is a short circuit proof open collector output to the negative (minus) rail, max. current 50 mA. The alarm output is typically used to activate a buzzer, LED or relay.

Delayed load disconnect and delayed reconnect

The load will be disconnected 90 seconds after the battery voltage drops below the preset level. If the battery voltage increases again to the connect threshold within this time period (after the engine has been started for example), the load will not be disconnected.
The load will be reconnected 30 seconds after the battery voltage has increased to more than the preset reconnect voltage.

Read more
178.17 EUR VAT included
The product is in stock
Details

Compara produse

You must add at least one product to compare products.

Was added to wishlist!

Was removed from wishlist!